Atmospheric Pressure Plasma Treatment of Glass Fibre Composite for Adhesion Improvement

被引：34

作者：

Kusano, Yukihiro ^{[1
]}

Mortensen, Henrik ^{[1
]}

Stenum, Bjarne ^{[1
]}

Kingshott, Peter ^{[2
]}

Andersen, Tom L. ^{[3
]}

Brondsted, Povl ^{[3
]}

Bilde-Sorensen, Jorgen B. ^{[3
]}

Sorensen, Bent F. ^{[3
]}

Bindslev, Henrik ^{[1
]}

机构：

[1] Riso Natl Lab, Opt & Plasma Res Dept, DK-4000 Roskilde, Denmark

[2] Riso Natl Lab, Danish Polymer Ctr, DK-4000 Roskilde, Denmark

[3] Riso Natl Lab, Mat Res Dept, DK-4000 Roskilde, Denmark

来源：

PLASMA PROCESSES AND POLYMERS | 2007年 / 4卷

关键词：

adhesion; dielectric barrier discharges (DBD); glass fibre reinforced polyester composite; plasma treatment;

D O I：

10.1002/ppap.200731206

中图分类号：

O59 [应用物理学];

学科分类号：

摘要：

Glass-fibre-reinforced polyester composite plates were treated with an atmospheric pressure dielectric barrier discharge. Synthetic air was used as the treatment gas. The water contact angle dropped markedly from 84 to 22 degrees after a 2-s treatment, and decreased to 0 degrees when the composite plates were treated for more than 30 s. X-Ray photoelectron spectroscopic analysis showed that the contents of aluminium and oxygen on the surface increased with the plasma treatment. The adhesion strength of the 2-s treated surface was comparable to or higher than that achieved by conventional mechanical surface roughening. It decreased when the surfaces were treated for 5 and 15 s, but recovered for 30-s treatment.

引用

页码：S455 / S459

页数：5

共 50 条

[41] Atmospheric Pressure Plasma Processing for Polymer Adhesion: A Review
Kusano, Yukihiro
JOURNAL OF ADHESION, 2014, 90 (09): : 755 - 777
[42] Effect of atmospheric pressure plasma treatment on interfacial adhesion between carbon fibers and polyimide
Qiu, Yiping
ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 2010, 240
[43] Plasma jet treatment of five polymers at atmospheric pressure: surface modifications and the relevance for adhesion
Noeske, M
Degenhardt, J
Strudthoff, S
Lommatzsch, U
INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2004, 24 (02) : 171 - 177
[44] Adhesion restraint of bubbles inside polymer tubes through atmospheric pressure plasma treatment
Material Science Laboratory, Mitsui Chemicals, Inc., 580-32, Nagaura, Sodegaura 299-0265
不详
IEEJ Trans. Fundam. Mater., 2006, 8 (813-820):
[45] Comparative Adhesion, Ageing Resistance, and Surface Properties of Wood Plastic Composite Treated with Low Pressure Plasma and Atmospheric Pressure Plasma Jet
Jesus Yanez-Pacios, Andres
Miguel Martin-Martinez, Jose
POLYMERS, 2018, 10 (06)
[46] Improvement and mechanism of interfacial adhesion in PBO fiber/bismaleimide composite by oxygen plasma treatment
Liu, Dong
Chen, Ping
Mu, Jujie
Yu, Qi
Lu, Chun
APPLIED SURFACE SCIENCE, 2011, 257 (15) : 6935 - 6940
[47] Air-to-air atmospheric pressure plasma treatment - perspective for composite manufacturing
Fang, Cheng
Cederlof, Daan Jonas Hottentot
Bardenshtein, Alexander
Kusanol, Yukihiro
41ST RISO INTERNATIONAL SYMPOSIUM ON MATERIALS SCIENCE: MATERIALS AND DESIGN FOR NEXT GENERATION WIND TURBINE BLADES, 2020, 942
[48] Improvement of Adhesion Properties of Polyamide 6 and Polyoxymethylene-Copolymer by Atmospheric Cold Plasma Treatment
Karoly, Zoltan
Kalacska, Gabor
Zsidai, Laszlo
Mohai, Miklos
Klebert, Szilvia
POLYMERS, 2018, 10 (12):
[49] Evaluation of Adhesion Improvement of a GFRP Treated with Atmospheric Plasma Torch
Martinez, M. A.
Velasco, F.
Abenojar, J.
Chiminelli, A.
Breto, R.
JOURNAL OF ADHESION, 2015, 91 (12): : 937 - 949
[50] Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment
Garg, Saurabh
Hurren, Chris
Kaynak, Akif
SYNTHETIC METALS, 2007, 157 (01) : 41 - 47

← 1 2 3 4 5 →