Corrosion and electrochemical evaluation of an Al-Si-Cu aluminum alloy in ethanol solutions

被引：39

作者：

Song, Guang-Ling ^{[1
]}

Liu, Minghong ^{[2
]}

机构：

[1] GM Global Res & Dev, Chem Sci & Mat Syst Lab, Warren, MI 48090 USA

[2] Meda Engn & Tech Serv, Southfield, MI 48075 USA

来源：

CORROSION SCIENCE | 2013年 / 72卷

关键词：

Al alloy; Ethanol fuel; Corrosion; SN-BI ALLOYS; IMPEDANCE SPECTROSCOPY; BEHAVIOR; FUEL; PROTECTION;

D O I：

10.1016/j.corsci.2013.03.009

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The corrosion of aluminum alloy AlSi8Cu3Fe(Zn) in ethanol and ethanol solutions containing 10 vol.% water and 10 vol.% acetic acid, respectively, was investigated by means of electrochemical impedance spectroscopy (EIS), polarization curve, immersion, optical microscopy, scanning electron microscopy and element mapping. The Al alloy in the ethanol and its solutions exhibited a capacitive loop in the measured Nyquist EIS spectra at high frequencies, which can be attributed to the ethanol's dielectric response. Addition of 10 vol.% acetic acid increased the ethanol corrosivity more significantly than the same amount of water addition. The Al-Si-Cu-Mg precipitated zones in the alloy were susceptible to corrosion attack due to the micro-galvanic effect by the Cu-containing precipitates. (C) 2013 Elsevier Ltd. All rights reserved.

引用

页码：73 / 81

页数：9

共 50 条

[31] Understanding the corrosion behavior by passive film evolution in Zn-containing Al-Si-Cu cast alloy
Wang, Rui
Wang, Dongtao
Nagaumi, Hiromi
Wu, Zibin
Li, Xinzhong
Zhang, Haitao
CORROSION SCIENCE, 2022, 205
[32] Influences of pouring temperature and cooling rate on microstructure and mechanical properties of casting Al-Si-Cu aluminum alloy
Xiaowu HU
ActaMetallurgicaSinica(EnglishLetters), 2012, 25 (04) : 272 - 278
[33] Influences of pouring temperature and cooling rate on microstructure and mechanical properties of casting Al-Si-Cu aluminum alloy
Hu, Xiaowu
Ai, Fanrong
Yan, Hong
ACTA METALLURGICA SINICA-ENGLISH LETTERS, 2012, 25 (04) : 272 - 278
[34] Compression Properties of Al/Al-Si-Cu Alloy Functionally Graded Aluminum Foam Fabricated by Friction Stir Processing Route
Hangai, Yoshihiko
Saito, Kousuke
Utsunomiya, Takao
Kitahara, Soichiro
Kuwazuru, Osamu
Yoshikawa, Nobuhiro
MATERIALS TRANSACTIONS, 2013, 54 (03) : 405 - 408
[35] Research on a Low Melting Point Al-Si-Cu (Ni) Filler Metal for 6063 Aluminum Alloy Brazing
Peng, Chengyin
Zhu, Dandan
Li, Kaifeng
Du, Xiang
Zhao, Fei
Wan, Mingpan
Tan, Yuanbiao
APPLIED SCIENCES-BASEL, 2021, 11 (09):
[36] Optimization of Engine Block Casting Process Based on New Aluminum Alloy Material of Al-Si-Cu System
Deng, Wei
Luo, Kun
Lei, Jilin
Song, Zhongmo
Xu, Yuanzhi
Zhang, Yong
INTERNATIONAL JOURNAL OF METALCASTING, 2024, 18 (04) : 3580 - 3598
[37] Influence of indium trace addition on the microstructure and precipitation hardening response in Al-Si-Cu casting aluminum alloy
Akopyan, T. K.
Belov, N. A.
Letyagin, N., V
Milovich, F. O.
Lukyanchuk, A. A.
Fortuna, A. S.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 831
[38] An evaluation of tribological and mechanical properties of Al-Si-Cu alloy with nano-clay particles reinforcement
Kamali, Fahimeh
Azadi, Mahboobeh
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2019, 233 (19-20) : 7062 - 7076
[39] Interfacial Heat Transfer during Die Casting of an Al-Si-Cu Alloy
Hamasaiid, A.
Wang, G.
Davidson, C.
Dour, G.
Dargusch, M. S.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2009, 40A (13): : 3056 - 3058
[40] The Impact of Major Alloying Elements and Refiner on the SDAS of Al-Si-Cu Alloy
Djurdievic, Mile
Pavlovic, Jelena
Byczynski, Glenn
PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2009, 46 (02): : 97 - 114

← 1 2 3 4 5 →