Numerical Investigation on the Effect of Squeegee Angle during Stencil Printing Process

被引：2

作者：

Rusdi, M. S. ^{[1
]}

Abdullab, M. Z. ^{[2
]}

Aziz, M. S. Abdul ^{[1
]}

Abdullah, M. K. ^{[3
]}

Bakar, A. A. ^{[3
]}

Abd Samad, M. H. S. ^{[4
]}

Rethinasamy, P. ^{[4
]}

Veerasamy, Sivakumar ^{[4
]}

Khor, C. Y. ^{[5
]}

机构：

[1] Univ Sains Malaysia, Sch Mech Engn, Engn Campus, Nibongtebal 14300, Penang, Malaysia

[2] Univ Sains Malaysia, Sch Aerosp Engn, Engn Campus, Nibongtebal 14300, Penang, Malaysia

[3] Univ Sains Malaysia, Sch Mat & Mineral Resources Engn, Engn Campus, Nibongtebal 14300, Penang, Malaysia

[4] Celest Malaysia Sdn Bhd, Plot 15,Jalan Hitech 2-3 Phase 1,Kulim Hitech Pk, Kulim 09000, Malaysia

[5] Univ Malaysia Perlis, Fac Engn Technol, Mech Dept, Aras 1,Blok S2,Kampus UniCITI Alam, Padang Besar 02100, Perlis, Malaysia

来源：

REGIONAL CONFERENCE ON MATERIALS AND ASEAN MICROSCOPY CONFERENCE 2017 (RCM & AMC 2017) | 2018年 / 1082卷

关键词：

SURFACE;

D O I：

10.1088/1742-6596/1082/1/012057

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The high requirement of smaller size, lighter weight, and high performance Printed Circuit Board (PCB) in electronic packaging has contributed to the wide application of stencil printing for soldering process. However, during stencil printing stage contributes major concern compared to other stages in Surface Mount Technology (SMT). Unsuitable process parameters can cause the soldering defects that can lead to product failure in further processes in the production line. An investigation has been conducted to predict the real-time observation of solder paste Sn96.5Ag3.0Cu0.5 (SAC305) filling process into stencil apertures as well as print quality in stencil printing by using Computational Fluid Dynamics (CFD) approach. A 3D-Dimensional stencil printing model was developed and simulated in ANSYS Fluent 17 of different angles. It is found that squeegee angle 60 degrees to 80 degrees has potential to obtain the good print quality of solder paste.

引用

页数：6

共 50 条

[21] The effect of solder paste particle size on the thixotropic behaviour during stencil printing
Krammer, Oliver
Gyarmati, Benjamin
Szilagyi, Andras
Illes, Balazs
Busek, David
Dusek, Karel
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2018, 262 : 571 - 576
[22] Fine pitch stencil printing process modeling and optimization
Li, Y
Mahajan, RL
Nikmanesh, N
JOURNAL OF ELECTRONIC PACKAGING, 1996, 118 (01) : 1 - 6
[23] Characterization of the solder paste release from small stencil apertures in the stencil printing process
Aravamudhan, S
Santos, D
Pham-Van-Diep, G
Andres, F
JOURNAL OF ELECTRONIC PACKAGING, 2005, 127 (03) : 340 - 352
[24] Investigating the Effect of Solder Paste Viscosity Change on the Pressure during Stencil Printing
Krammer, Oliver
Varga, Bertalan
Krammer, Oliver
Busek, David
2016 IEEE 22ND INTERNATIONAL SYMPOSIUM FOR DESIGN AND TECHNOLOGY AND ELECTRONIC PACKAGING (SIITME), 2016, : 36 - 39
[25] Developing a robust stencil printing process for diverse interconnection technologies
Alawani, AD
Srihari, K
DiLella, J
PAN PACIFIC MICROELECTRONICS SYMPOSIUM, 2001, PROCEEDINGS, 2001, : 416 - 428
[26] Stencil printing process of buffer layer for wafer level CSP
Ezawa, H
Seto, M
Miyata, M
Tazawa, H
2001 INTERNATIONAL SYMPOSIUM ON MICROELECTRONICS, PROCEEDINGS, 2001, 4587 : 95 - 99
[27] A realtime process control system for solder paste stencil printing
Venkateswaran, S
Srihari, K
Adriance, JH
Westby, GR
TWENTY FIRST IEEE/CPMT INTERNATIONAL ELECTRONICS MANUFACTURING TECHNOLOGY SYMPOSIUM, 1997, : 62 - 67
[28] Numerical Investigation to Influence of Perforation Angle on Hydraulic Fracturing Process
Bu, Lin
Li, Shucai
Shi, Shaoshuai
Xie, Xiaokun
Li, Liping
Zhou, Zongqing
GEOTECHNICAL AND GEOLOGICAL ENGINEERING, 2019, 37 (03) : 1125 - 1133
[29] Numerical Investigation to Influence of Perforation Angle on Hydraulic Fracturing Process
Lin Bu
Shucai Li
Shaoshuai Shi
Xiaokun Xie
Liping Li
Zongqing Zhou
Geotechnical and Geological Engineering, 2019, 37 : 1125 - 1133
[30] Adaptive optimal control of stencil printing process using reinforcement learning
Khader, Nourma
Yoon, Sang Won
ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING, 2021, 71

← 1 2 3 4 5 →