Fabrication and optimization of AA5754/SiC nanocomposites via friction-stir processing (FSP)

被引:1
|
作者
Rezaei, Morteza [1 ]
Davari, Ali [1 ]
Mirhosseini, Seyyed Saber [1 ]
Shamsipur, Ali [1 ]
机构
[1] Amirkabir Univ Technol, Dept Mat Sci & Engn, Tehran, Iran
关键词
nanocomposites; aluminum surface composite (ASC); 5754 aluminum alloys; friction-stir processing (FSP); SiC nanoparticles; SILICON-CARBIDE; MECHANICAL-PROPERTIES; CORROSION BEHAVIOR; ALUMINUM; PERFORMANCE; COMPOSITES; PARAMETERS;
D O I
10.1051/metal/2023015
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
Metal-matrix composites (MMC) are cost-effective alternatives to steel and iron resources. This research investigates the properties of the nanocomposites created by SiC nanoparticles. AA5754 was chosen as a matrix and fabricated by friction-stir processing (FSP). The effects of input parameters, including rotational/traverse speeds, number of passes on the microhardness, and topography, were studied through the response surface methodology. Each parameter was selected in three levels, and other parameters were considered constant. To examine the effect of SiC nanoparticles, optical microscopy (OM), SEM, and microhardness tests were used. Due to the distribution of SiC nanoparticles and homogeneous microstructure coinciding with high microhardness, the optimal rotational speed, traverse speed, and the number of passes at 500 rpm, 20 mm/min, and 3 were obtained, respectively. Also, the average microhardness profile and the average grain size in the SZ region for the optimal sample were equal to 68 Vickers and 1.5 Microns, respectively. The results showed that increasing the number of passes accrued appropriate nanoparticle distribution. During operation, various mechanisms occurred, such as nucleation during recrystallization and placement of SiC nanoparticles at the grain boundaries, which prevent grain boundary migration and inhibit grain growth.
引用
收藏
页数:13
相关论文
共 50 条
  • [31] Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy
    Manoj Mohan Prasath, V.
    Dharani Kumar, S.
    Mohammed Raffic, N.
    Journal of Adhesion Science and Technology, 2024,
  • [32] Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy
    Prasath, V. Manoj Mohan
    Kumar, S. Dharani
    Raffic, N. Mohammed
    JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2025, 39 (06) : 879 - 909
  • [33] Investigation of internal defects and premature fracture of dissimilar refill friction stir spot welds of AA5754 and AA6061
    Ferreira, Antonio Cappelletti
    Campanelli, Leonardo Contri
    Suhuddin, Uceu Fuad Hasan
    de Alcantara, Nelson Guedes
    dos Santos, Jorge Fernandez
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 106 (7-8): : 3523 - 3531
  • [34] Experimental investigation of Mg/SiC composite fabrication via friction stir processing
    Naser, Ahmed Z.
    Darras, Basil M.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 91 (1-4): : 781 - 790
  • [35] Experimental investigation of Mg/SiC composite fabrication via friction stir processing
    Ahmed Z. Naser
    Basil M. Darras
    The International Journal of Advanced Manufacturing Technology, 2017, 91 : 781 - 790
  • [36] Heat Input and Mechanical Properties Investigation of Friction Stir Welded AA5083/AA5754 and AA5083/AA7020
    Ahmed, Mohamed M. Z.
    Ataya, Sabbah
    El-Sayed Seleman, Mohamed M.
    Mahdy, Abdalla M. A.
    Alsaleh, Naser A.
    Ahmed, Essam
    METALS, 2021, 11 (01) : 1 - 20
  • [37] Experimental investigation of Mg/SiC composite fabrication via friction stir processing
    Darras, Basil M. (bdarras@aus.edu), 1600, Springer London (91): : 1 - 4
  • [38] Effect of welding motion and pre-/post-annealing of friction stir welded AA5754 joints
    Cabibbo, M.
    Forcellese, A.
    Simoncini, M.
    Pieralisi, M.
    Ciccarelli, D.
    MATERIALS & DESIGN, 2016, 93 : 146 - 159
  • [39] Friction Stir Processing of AA3105/SiC Composites Constructed Through the Sandwich Method: The Effects of FSP Variables
    Meraj Houshyar
    Salman Nourouzi
    Hamed Jamshidi Aval
    Transactions of the Indian Institute of Metals, 2021, 74 : 429 - 438
  • [40] Study of friction stir butt welding between thin plates of AA5754 and mild steel for automotive applications
    P. N. Karakizis
    D. I. Pantelis
    D. A. Dragatogiannis
    V. D. Bougiouri
    C. A. Charitidis
    The International Journal of Advanced Manufacturing Technology, 2019, 102 : 3065 - 3076