Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

被引:5
|
作者
Jeong, H. T. [1 ]
Lee, S. W. [1 ]
Kim, W. J. [1 ]
机构
[1] Hongik Univ, Dept Mat Sci & Engn, Sangsu Dong 72-1, Seoul 121791, South Korea
关键词
Magnesium-lithium alloy; Superplasticity; Severe plastic deformation; Grain size; Grain growth; LOW-TEMPERATURE SUPERPLASTICITY; MG-LI ALLOYS; ELEVATED-TEMPERATURE; PHASE-TRANSFORMATION; AL; BEHAVIOR; MAPS; MICROSTRUCTURE; DIFFUSION; CREEP;
D O I
10.1016/j.jma.2024.01.001
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
The superplastic behavior and associated deformation mechanisms of a fine-grained Mg -10.1 Li-0.8Al-0.6Zn alloy (LAZ1011) with a grain size of 3.2 mu m, primarily composed of the BCC )5 phase and a small amount of the HCP alpha phase, were examined in a temperature range of 473 K to 623 K. The microstructural refinement of this alloy was achieved by employing high -ratio differential speed rolling. The best superplasticity was achieved at 523 K and at strain rates of 10-4 -5 x 10-4 s-1, where tensile elongations of 550-600% were obtained. During the heating and holding stage of the tensile samples prior to tensile loading, a significant increase in grain size was observed at temperatures above 573 K. Therefore, it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms. In the investigated strain rate range, the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding, while at high strain rates, lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism. It was concluded that solute drag creep is unlikely to occur. During the late stages of deformation at 523 K, it was observed that grain boundary sliding led to the agglomeration of the alpha phase, resulting in significant strain hardening. Deformation mechanism maps were constructed for )5 -Mg -Li alloys in the form of 2D and 3D formats as a function of strain rate, stress, temperature, and grain size, using the constitutive equations for various deformation mechanisms derived based on the data of the current tests. (c) 2024 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/ ) Peer review under responsibility of Chongqing University
引用
收藏
页码:316 / 331
页数:16
相关论文
共 50 条
  • [41] Mechanical properties of fine-grained flame resistant magnesium alloys processed with severe plastic deformation
    Takasu H.
    Kimura K.
    Yukutake E.
    Ito T.
    Noda M.
    Somekawa H.
    Tsuchiya K.
    Kuramoto S.
    Keikinzoku Yosetsu/Journal of Light Metal Welding, 2022, 60 (02): : 34 - 41
  • [42] Enhanced superplasticity of ultrafine-grained alloys processed by severe plastic deformation
    Valiev, RZ
    Islamgaliev, RK
    TOWARDS INNOVATION IN SUPERPLASTICITY II, 1999, 304-3 : 39 - 46
  • [43] Cavitation behavior of fine-grained 1420 Al-Li alloy during superplastic deformation
    Shao, J.
    Guo, H. P.
    Li, Z. Q.
    Han, X. Q.
    SUPERPLASTICITY IN ADVANCED MATERIALS, 2007, 551-552 : 633 - +
  • [44] Development of fine grained structures using severe plastic deformation
    Horita, Z
    Furukawa, M
    Nemoto, M
    Langdon, TG
    MATERIALS SCIENCE AND TECHNOLOGY, 2000, 16 (11-12) : 1239 - 1245
  • [45] Deformation mechanisms in fine-grained Ti-Al alloys
    Morris, MA
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1997, 224 (1-2): : 12 - 20
  • [46] Severe plastic deformation technologies for ultra fine grained alloys
    Canta, T.
    Frunza, D.
    MATERIALS AND TECHNOLOGIES, 2007, 23 : 33 - 38
  • [47] Deformation mechanisms in fine-grained Ti-Al alloys
    Univ of Neuchatel, Neuchatel, Switzerland
    Mater Sci Eng A Struct Mater Prop Microstruct Process, 1600, 1-2 (12-20):
  • [48] Positron annihilation studies of microstructure of ultra fine grained metals prepared by severe plastic deformation
    Cízek, J
    Procházka, I
    Smola, B
    Stulíková, I
    Kuzel, R
    Cieslar, M
    Matej, Z
    Cherkaska, V
    Brauer, G
    Anwand, W
    Islamgaliev, RK
    Kulyasova, O
    MATERIALS STRUCTURE & MICROMECHANICS OF FRACTURE IV, 2005, 482 : 207 - 210
  • [49] Hot deformation behavior of uniform fine-grained GH4720Li alloy based on its processing map
    Qiu-ying Yu
    Zhi-hao Yao
    Jian-xin Dong
    International Journal of Minerals Metallurgy and Materials, 2016, 23 (01) : 83 - 91
  • [50] Hot deformation behavior of uniform fine-grained GH4720Li alloy based on its processing map
    Qiu-ying Yu
    Zhi-hao Yao
    Jian-xin Dong
    International Journal of Minerals, Metallurgy, and Materials, 2016, 23 : 83 - 91