Multilayer Clad Plate of Stainless Steel/Aluminum/ Aluminum Alloy

被引：0

作者：

袁家伟 ^{[1
]}

庞玉华 ^{[1
]}

机构：

[1] School of Metallurgy Engineering, Xi’an University of Architecture & Technology

来源：

Journal of Wuhan University of Technology(Materials Science) | 2011年 / 01期

关键词：

multilayer clad plate; hot rolling; bonding strength; stretch strength;

D O I：

暂无

中图分类号：

TG146.21 [];

学科分类号：

080502 ;

摘要：

The 3, 5, 20 layer clad plate from austenitic stainless steel, pure aluminum and aluminum alloy sheets were fabricated in different ways. The stretch and interface properties were measured. The result shows that 20 layer clad plate is better than the others. Well-bonded clad plate was successfully obtained in the following procedure: Basic clad sheet from 18 layer Al1060/Al3003 sheets was firstly obtained with an initial rolling reduction of 44% at 450 ℃, followed by annealing at 300 ℃, and then with reduction of 50% at 550 ℃ from STS304 on each side. The best 20 layer clad plate was of 129 MPa bonding strength and 225 MPa stretch strength.

引用

页码：111 / 113

页数：3

共 50 条

[11] Interface properties of copper/aluminum/stainless steel clad materials
Bae, Dong-Su
Kim, Soon-Kook
Lee, Sang-Pill
Shibayama, Tamaki
Bae, Dong-Hyun
MECHANICAL BEHAVIOR OF MATERIALS X, PTS 1AND 2, 2007, 345-346 : 1497 - +
[12] Interfacial strength and structure of stainless steel-semi-solid aluminum alloy clad metal
Liu, HW
Guo, C
Cheng, Y
Liu, XF
Shao, GJ
MATERIALS LETTERS, 2006, 60 (02) : 180 - 184
[13] Properties of aluminum alloy/stainless steel clad material produced via vacuum roll bonding
Mitsubishi Heavy Industries Ltd, Nagasaki, Japan
Weld World Soudage Monde, 2 (88-96):
[14] Press-formability of aluminum clad stainless steel sheet
Mori, T
Kurimoto, S
Abraha, PA
JSME INTERNATIONAL JOURNAL SERIES C-DYNAMICS CONTROL ROBOTICS DESIGN AND MANUFACTURING, 1996, 39 (02): : 404 - 410
[15] Air bending and springback of stainless steel clad aluminum sheet
Yilamu, K.
Hino, R.
Hamasaki, H.
Yoshida, F.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2010, 210 (02) : 272 - 278
[16] THE PROPERTIES AND FORMABILITY OF ALUMINUM-5-PERCENT MAGNESIUM ALLOY CLAD WITH AN AUSTENITIC STAINLESS-STEEL
MURRAY, BW
ROBERTS, WT
WILSON, DV
MEMOIRES SCIENTIFIQUES DE LA REVUE DE METALLURGIE, 1980, 77 (04): : 607 - 616
[17] Fabrication of iron aluminum alloy/steel laminate by clad rolling
Masahashi, N
Komatsu, K
Kimura, G
Watanabe, S
Hanada, S
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2006, 37A (05): : 1665 - 1673
[18] Fabrication of iron aluminum alloy/steel laminate by clad rolling
N. Masahashi
S. Watanabe
S. Hanada
K. Komatsu
G. Kimura
Metallurgical and Materials Transactions A, 2006, 37 : 1665 - 1673
[19] Tensile deformation behavior of stainless steel clad aluminum bilayer sheet
Choi, SH
Kim, KH
Oh, KH
Lee, DN
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1997, 222 (02): : 158 - 165
[20] Application of the direct resistance heating for stainless steel/aluminum clad manufacturing process
Hamada, K
Isaka, K
Doi, D
Yonemitsu, Y
Iwasaki, S
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2002, 88 (02): : 66 - 72

← 1 2 3 4 5 →