IMPROVING THE PROPERTIES OF ALLOY AL4 MELTED FROM CHARGES INCLUDING SECONDARY SILUMINS.

被引：0
|
作者：
Galushko, A.M.
Markarov, Yu.V.
Nemenenok, B.M.
Strizhenkov, M.I.
机构：
来源：
Soviet Castings Technology (English Translation of Liteinoe Proizvodstvo) | 1986年 / 01期
关键词：
ALUMINUM CASTINGS - DIE CASTINGS;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Over 30 grades of secondary silumin are produced from scrap and recycled materials in the USSR. Experience at the Minsk Engine Works and the Altai group of engine producers has shown that secondary silumins can be recycled as part of the charge used to melt alloy AL4. All the above foundries replace virgin silumins by a proportion (up to 20%) of secondary alloy AK9. The scope for using a wider range of secondary silumins in this way has been explored. The alloy AL4 melts were made in a 125 kg pouring furnace with a cast iron crucible. The melt composition was adjusted to correspond to the requirements of GOST left bracket All-Union State Standard right bracket 2685-75. Tensile testpieces conforming to GOST 2685-75 were poured in cast iron sample molds preheated to 200-210 degree C.
引用
收藏
页码：22 / 25
相关论文
共 50 条
  • [31] Microstructure and anisotropic mechanical properties of selective laser melted Ti6Al4V alloy under different scanning strategies
    Zheng, Zhongpeng
    Jin, Xin
    Bai, Yuchao
    Yang, Yun
    Ni, Chenbing
    Lu, Wen Feng
    Wang, Hao
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 831
  • [32] Investigation into the microstructure and dynamic compressive properties of selective laser melted Ti-6Al-4V alloy with different heating treatments
    Liu, Yang
    Xu, Huaizhong
    Zhu, Lei
    Wang, Xiaofeng
    Han, Quanquan
    Li, Shuxin
    Wang, Yonggang
    Setchi, Rossitza
    Wang, Di
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 805
  • [33] Improving the tribological properties of Ti-6Al-4V alloy by nitrogen-ion implantation
    Itoh, Y
    Itoh, A
    Azuma, H
    Hioki, T
    SURFACE & COATINGS TECHNOLOGY, 1999, 111 (2-3): : 172 - 176
  • [34] Improving the tribological properties of Ti-6Al-4V alloy by nitrogen-ion implantation
    Itoh, Y.
    Itoh, A.
    Azuma, H.
    Hioki, T.
    Surface and Coatings Technology, 1999, 111 (2-3): : 172 - 176
  • [35] Several plasma diffusion processes for improving wear properties of Ti6Al4V alloy
    Yetim, A. F.
    Yildiz, F.
    Vangolu, Y.
    Alsaran, A.
    Celik, A.
    WEAR, 2009, 267 (12) : 2179 - 2185
  • [36] Improving the mechanical properties of Ti-6Al-4V alloy by equal channel angular pressing
    Saitova, LR
    Semenova, IP
    Raab, GI
    Valiev, RZ
    Lowe, TC
    Zhu, YT
    NANOSTRUCTURED MATERIALS BY HIGH-PRESSURE SEVERE PLASTIC DEFORMATION, 2006, 212 : 241 - +
  • [37] THERMODYNAMIC PROPERTIES OF SYNTHETIC BASIC ALUMINITE [AL4(OH)10SO4.5H2O] FROM SOLUBILITY DATA
    SINGH, SS
    CANADIAN JOURNAL OF SOIL SCIENCE, 1980, 60 (02) : 381 - 384
  • [38] Influence of process parameter and strain rate on the dynamic compressive properties of selective laser-melted Ti-6Al-4V alloy
    Pang, Zhicong
    Liu, Yang
    Li, Ming
    Zhu, Chunli
    Li, Shuxin
    Wang, Yonggang
    Wang, Di
    Song, Changhui
    APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING, 2019, 125 (02):
  • [39] Forming quality and mechanical properties of selective laser melted Ti6Al4V alloy with ultra-high scanning speed
    Deng, Hongwen
    Wang, Yudai
    Cheng, Xu
    Wang, Huaming
    Wang, Shuaiqi
    Zhang, Yi
    Cui, Zhuodan
    Xiong, Lin
    Zhang, Shuquan
    OPTICS AND LASER TECHNOLOGY, 2025, 186
  • [40] Densification, Tailored Microstructure, and Mechanical Properties of Selective Laser Melted Ti-6Al-4V Alloy via Annealing Heat Treatment
    Wang, Di
    Wang, Han
    Chen, Xiaojun
    Liu, Yang
    Lu, Dong
    Liu, Xinyu
    Han, Changjun
    MICROMACHINES, 2022, 13 (02)
12345