Engineering calculation of forming pressure for copper alloy valve of gas appliance by squeeze casting

被引：0
|
作者：
Yin, F. [1 ]
Wang, G.X. [1 ]
Hong, S.Z. [1 ]
Zeng, Z.P. [1 ]
机构：
[1] Sch. of Mat. Sci. and Eng., Shanghai Jiaotong Univ., Shanghai 200030, China
来源：
Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University | 2000年 / 34卷 / 12期
关键词：
Calculations - Metal casting - Pressure - Pressure pouring - Valves (mechanical);
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The copper alloy valve of the gas appliance is manufactured with the squeeze casting replacing the die casting under pressure. Not only are the defects of gas holes and non-metal inclusion in the die casting under pressure eliminated, but also the rate of production is increased while the cost of production is decreased. The forming process of the valve by the squeeze casting was analyzed. Based on it, the simplified pattern for calculating the forming pressure was presented and the formula was derived from the formation work method. An example was given to explain the problem. The comparison of the calculated results with the measured results shows good coincidence.
引用
收藏
页码：1635 / 1637
相关论文
共 50 条
  • [21] A model for prediction of pressure and redistribution of gas-forming elements in multicomponent casting alloys
    S. D. Felicelli
    D. R. Poirier
    P. K. Sung
    Metallurgical and Materials Transactions B, 2000, 31 : 1283 - 1292
  • [22] A model for prediction of pressure and redistribution of gas-forming elements in multicomponent casting alloys
    Felicelli, SD
    Poirier, DR
    Sung, PK
    METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2000, 31 (06): : 1283 - 1292
  • [23] Development of a copper alloy composition for gravity, low-pressure, and high-pressure die casting
    Haupt, R.H.
    Transactions of the American Foundrymen's Society, 1990,
  • [24] Gas hole characteristics and forming mechanism of oxygen free copper rod with up-casting
    Yuan, Gecheng
    Wang, Peiyu
    Li, Zuojian
    Tezhong Zhuzao Ji Youse Hejin/Special Casting & Nonferrous Alloys, 1997, (05): : 13 - 15
  • [25] A study on joining magnesium alloy high pressure die casting components with thread forming fasteners
    Wang, Gerry Gang
    Bos, Jeremy
    JOURNAL OF MAGNESIUM AND ALLOYS, 2018, 6 (02) : 114 - 120
  • [26] The effect of squeeze casting pressure and iron content on the impact energy of Al-7Si-0.7Mg alloy
    Chen, ZW
    Thorpe, WR
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1996, 221 (1-2): : 143 - 153
  • [27] Effect of squeeze casting pressure and iron content on the impact energy of Al-7Si-0.7Mg alloy
    CSIRO Div of Manufacturing, Technology, Kenmore
    Mater Sci Eng A Struct Mater Prop Microstruct Process, 1-2 (143-153):
  • [28] APPLICABILITY OF A COPPER ALLOY TO DIE MOLD FOR SQUEEZE CASTING (THE DEVELOPMENT OF MOLD STEELS WITH EXCELLENT THERMAL FATIGUE PROPERTIES-V).
    Mori, Tokihiko
    Hosomi, Koji
    Mizuno, Yukitaka
    Terabayashi, Takeshi
    Nakagawa, Tomokazu
    1600, (25):
  • [29] Gas-pressure forming behavior and modeling of superplastic Al 5083 alloy
    Syn, CK
    O'Brien, MJ
    Lesuer, DR
    Sherby, OD
    MODELING THE PERFORMANCE ENGINEERING STRUCTURAL MATERIALS II, 2001, : 307 - 316
  • [30] THE DEVELOPMENT OF MOLD STEELS WITH EXCELLENT THERMAL FATIGUE PROPERTIES .5. APPLICABILITY OF A COPPER ALLOY TO DIE MOLD FOR SQUEEZE CASTING
    MORI, T
    HOSOMI, K
    MIZUNO, Y
    TERABAYASHI, T
    NAKAGAWA, T
    TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (11) : B321 - B321
12345