Development of strip edger between finishing mill stands - width rolling characteristics of strip edging

被引：0

作者：

Tazoe, Nobuhiro ^{[1
]}

Kawamura, Kunio ^{[1
]}

Sato, Kun-ichi ^{[1
]}

Igarashi, Yasuo ^{[1
]}

Fujishima, Ikuo ^{[1
]}

Torii, Mitsuo ^{[1
]}

Honjo, Hisashi ^{[1
]}

Matoba, Tetsu ^{[1
]}

Shiozaki, Hiroyuki ^{[1
]}

Ohya, Kiyoshi ^{[1
]}

机构：

[1] IHI, Japan

来源：

IHI Engineering Review (English Edition) | 1988年 / 21卷 / 01期

关键词：

Models - Sheet and Strip Metal--Shearing;

D O I：

暂无

中图分类号：

TG [金属学与金属工艺];

学科分类号：

0805 ;

摘要：

With the aim of developing an edger for installation between the finishing stands, a 1/10 model mill was tested using a hard lead strip as a model strip. As a result, basic characteristics of strip edging under tension were made clear. And next, a strip edger was installed between finishing stands of the hot strip mill line at Nippon Steel Corporation's Nagoya Works where experiments were conducted under various conditions. As a result, it was clarified that the strip edger between the latter finishing stands was effective to control strip width. And pressure multiplication factor of the strip edging, which was calculated from the measured rolling load during the experiments, was nearly equal to the results from the model experiment with hard lead plate.

引用

页码：14 / 19

共 50 条

[41] DEVELOPMENT OF WIDTH CONTROL MODEL FOR HOT STRIP MILL
ORITA, K
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1146 - 1146
[42] Correlation analysis between looper system and strip width narrowing in hot strip rolling
Feng-wei Jing
Zhao-yu Chen
Jie Li
Qiang Guo
International Journal on Interactive Design and Manufacturing (IJIDeM), 2023, 17 : 539 - 551
[43] Synchronous control for the hydraulic width system of Edger Rolling Mill
Ning Shurong
Fan Zhuoyu
SEVENTH INTERNATIONAL SYMPOSIUM ON INSTRUMENTATION AND CONTROL TECHNOLOGY: OPTOELECTRONIC TECHNOLOGY AND INSTUMENTS, CONTROL THEORY AND AUTOMATION, AND SPACE EXPLORATION, 2008, 7129
[44] Correlation analysis between looper system and strip width narrowing in hot strip rolling
Jing, Feng-wei
Chen, Zhao-yu
Li, Jie
Guo, Qiang
INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM, 2023, 17 (02): : 539 - 551
[45] Effect of deformation between stands on the strip shape in hot rolling
Wu, QH
Zhang, J
Wang, CS
Wei, GC
Song, P
Deng, CG
JOURNAL OF UNIVERSITY OF SCIENCE AND TECHNOLOGY BEIJING, 2000, 7 (03): : 222 - 224
[46] Effect of Deformation between Stands on the Strip Shape in Hot Rolling
Qinghai Wu
Wuhan Iron & Steel Corporation)
International Journal of Minerals,Metallurgy and Materials, 2000, (03) : 222 - 224
[47] CALCULATION OF PROGRESS OF TEMPERATURES IN FINISHING TRAIN OF A HOT ROLLING MILL FOR WIDE STRIP
PAWELSKI, O
STAHL UND EISEN, 1969, 89 (21): : 1146 - &
[48] Development of interstand velocimeter for hot strip finishing mill d
Isei, Yoshito
Yakita, Yukihiko
Buei, Yasuhiko
2006 SICE-ICASE INTERNATIONAL JOINT CONFERENCE, VOLS 1-13, 2006, : 151 - +
[49] WEAR MECHANISM OF WORK ROLL FOR REAR STANDS OF FINISHING TRAIN IN HOT STRIP MILL
NISHIMURA, Y
SANO, Y
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (06) : B184 - B184
[50] Efficiency of "Secondary" Actuators of Flatness and Crown Control in the Finishing Stands of the Hot Strip Mill
Nikitenko, E.
AISTECH 2013: PROCEEDINGS OF THE IRON & STEEL TECHNOLOGY CONFERENCE, VOLS I AND II, 2013, : 1587 - 1590

← 1 2 3 4 5 →