Development of strip edger between finishing mill stands - width rolling characteristics of strip edging

被引：0

作者：

Tazoe, Nobuhiro ^{[1
]}

Kawamura, Kunio ^{[1
]}

Sato, Kun-ichi ^{[1
]}

Igarashi, Yasuo ^{[1
]}

Fujishima, Ikuo ^{[1
]}

Torii, Mitsuo ^{[1
]}

Honjo, Hisashi ^{[1
]}

Matoba, Tetsu ^{[1
]}

Shiozaki, Hiroyuki ^{[1
]}

Ohya, Kiyoshi ^{[1
]}

机构：

[1] IHI, Japan

来源：

IHI Engineering Review (English Edition) | 1988年 / 21卷 / 01期

关键词：

Models - Sheet and Strip Metal--Shearing;

D O I：

暂无

中图分类号：

TG [金属学与金属工艺];

学科分类号：

0805 ;

摘要：

With the aim of developing an edger for installation between the finishing stands, a 1/10 model mill was tested using a hard lead strip as a model strip. As a result, basic characteristics of strip edging under tension were made clear. And next, a strip edger was installed between finishing stands of the hot strip mill line at Nippon Steel Corporation's Nagoya Works where experiments were conducted under various conditions. As a result, it was clarified that the strip edger between the latter finishing stands was effective to control strip width. And pressure multiplication factor of the strip edging, which was calculated from the measured rolling load during the experiments, was nearly equal to the results from the model experiment with hard lead plate.

引用

页码：14 / 19

共 50 条

[21] CHARACTERISTICS OF METAL DEFORMATION BY STRIP EDGING (STUDY ON STRIP EDGING - II).
Tazoe, Nobuhiro
Honjyo, Hisashi
Shiozaki, Hiroyuki
Watanabe, Hajime
Ono, Takeshi
Ataka, Matsuo
1600, (24):
[22] Development of a shadow finishing mill set-up for hot strip rolling
Rudkins, NT
Holmes, K
METAL FORMING 2000, 2000, : 269 - 276
[23] Microstructural, mechanical and tribological characterisation of roll materials for the finishing stands of the hot strip mill for steel rolling
Nilsson, M.
Olsson, M.
WEAR, 2013, 307 (1-2) : 209 - 217
[24] An investigation of worn work roll materials used in the finishing stands of the hot strip mill for steel rolling
Nilsson, M.
Olsson, M.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2013, 227 (08) : 837 - 844
[25] Research and Application for Finishing Hot Mill Strip Width Model
Song, Xiang Rong
Liu, Zhi Qiang
2020 CHINESE AUTOMATION CONGRESS (CAC 2020), 2020, : 5262 - 5266
[26] STUDY ON STRIP EDGING .2. CHARACTERISTICS OF METAL DEFORMATION BY STRIP EDGING
TAZOE, N
HONJYO, H
SHIOZAKI, H
WATANABE, H
ONO, T
ATAKA, M
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1984, 24 (05) : B150 - B150
[27] Development of width control system in hot strip mill. (Performance test result on actual AWC edger)
Hino, Hiroyuki
Ozono, Ryuichi
Tsukamoto, Hidehiko
Tsukuda, Kazuhiro
Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 1990, 56 (526): : 1620 - 1625
[28] Study on the Formulas of the Dog-bone Shape of Edger Rolling in Hot Strip Mill
Wang, Aili
Yang, Quan
Liu, Huaqiang
Du, Xiaozhong
Wang, Xiaochen
MANUFACTURING SCIENCE AND ENGINEERING, PTS 1-5, 2010, 97-101 : 2871 - 2875
[29] DEVELOPMENT OF SLAB WIDTH CONTROL-SYSTEM FOR HDR .2. DEVELOPMENT OF WIDTH CONTROL-SYSTEM BY ROUGHING MILL EDGER IN HOT STRIP MILL
WAKAMATSU, Y
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1986, 72 (12): : 1231 - 1231
[30] Roll wear prediction model for finishing stands of hot strip mill
John, S
Sikdar, S
Mukhopadhyay, A
Pandit, A
IRONMAKING & STEELMAKING, 2006, 33 (02) : 169 - 175

← 1 2 3 4 5 →