Effect of heat treatment on microstructure and corrosion behavior of Al[sbnd]Cu alloy fabricated by wire arc additive manufacturing

被引：0
|
作者：
Ren, Guochun [1 ,3 ]
Zheng, Yang [1 ,2 ,3 ]
Xiong, Ruize [1 ,3 ]
Zhao, Cenya [2 ,3 ]
Wang, Tianqi [1 ,3 ]
Li, Liangyu [1 ,3 ]
机构：
[1] School of Mechanical Engineering, Tiangong University, Tianjin,300387, China
[2] School of Aeronautics and Astronautics, Tiangong University, Tianjin,300387, China
[3] Tianjin Area Major Laboratory of Advanced Mechatronics Equipment Technology, Tianjin,300387, China
来源：
Materials Characterization | 2024年 / 218卷
关键词：
This study investigated the effect of heat treatment on the microstructure and corrosion behavior of the Wire Arc Additive Manufacturing (WAAM) 2319 Al alloy. The results showed that the solid solution treatment and the artificial ageing significantly increased the microhardness of the alloy; and the second phase of the alloy changed from a continuous to a dispersed distribution. Heat treatment led to an increase in pores; and the number of small-size pores increased significantly with the ageing time; this increased the risk of crevice corrosion. The as-deposited WAAM 2319 Al alloy; characterized by an α-Al matrix and coarse intergranular intermetallics Al2Cu; underwent galvanic corrosion; which severely damaged the passivation film. The solid solution treatment alleviated this by dissolving the coarse intergranular intermetallics and improving corrosion resistance. During artificial ageing; the corrosion potential decreased gradually as the size and number of precipitated phases increased. Pitting corrosion was the most severe; and corrosion resistance was lowest in the solid solution + peak ageing state. © 2024 Elsevier Inc;
D O I：
10.1016/j.matchar.2024.114516
中图分类号：
学科分类号：
摘要：
引用
收藏
相关论文
共 50 条
  • [21] EFFECT OF POST-HEAT TREATMENT ON THE MECHANICAL PROPERTIES AND CORROSION BEHAVIOR OF DUPLEX STAINLESS STEEL FABRICATED By WIRE ARC ADDITIVE MANUFACTURING
    Zhang, Long
    Liu, Liang
    Liu, Feihong
    Sun, Jian
    Wang, Dongsheng
    ARCHIVES OF METALLURGY AND MATERIALS, 2024, 69 (02) : 667 - 674
  • [22] Heat Treatment Optimization of 2219 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing
    Yang, Jiannan
    Ni, Yunqiang
    Li, Hui
    Fang, Xuewei
    Lu, Bingheng
    COATINGS, 2023, 13 (03)
  • [23] Microstructure evolution and strengthening behavior of maraging steel fabricated by wire arc additive manufacturing at different heat treatment processes
    Kan, Chengling
    Zhao, Lin
    Cao, Yang
    Ma, Chengyong
    Peng, Yun
    Tian, Zhiling
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 909
  • [24] Research on hot deformation behavior and microstructure characterization of the NiTi alloy fabricated by wire arc additive manufacturing
    Chen, Xiaochun
    Chen, Hongsheng
    Nie, Huihui
    Wang, Wenxian
    Zheng, Liuwei
    Zhou, Jun
    Journal of Materials Research and Technology, 2024, 33 : 9180 - 9194
  • [25] Effect of induction heat treatment on microstructure, mechanical and corrosion properties of stainless steel 308 L fabricated using wire arc additive manufacturing
    Yangfan Sun
    Xianglong Li
    Lai Xu
    Hongyao Shen
    Yougen Liu
    Scientific Reports, 14 (1)
  • [26] Effect of Heat Treatment on Microstructure of Al0.78CoCrFeNi Alloy Fabricated by Laser Additive Manufacturing
    Nie, Xiaowu
    Lv, Yanbiao
    JOM, 2024, 76 (02) : 843 - 852
  • [27] Effect of Heat Treatment on Microstructure of Al0.78CoCrFeNi Alloy Fabricated by Laser Additive Manufacturing
    Xiaowu Nie
    Yanbiao Lv
    JOM, 2024, 76 : 843 - 852
  • [28] Effect of Cu content on microstructure and properties of Ti-6Al-4V alloy fabricated by double-wire arc additive manufacturing
    Tian, Yinbao
    Liang, Zhetao
    Zhang, Guoyang
    Liu, Hongqiang
    Jiang, Zhengyi
    Zhang, Xin
    Wang, Jingling
    Han, Jian
    Zhao, Xiaoxin
    MATERIALS TODAY COMMUNICATIONS, 2024, 39
  • [29] Microstructure and corrosion behaviour of structural steel fabricated by wire arc additive manufacturing (WAAM)
    Dong, Zheng
    Torbati-Sarraf, Hamidreza
    Huang, Cheng
    Xu, Ke
    Gu, Xiang-Lin
    Fu, Chuanqing
    Liu, Xingjian
    Meng, Zhou
    MATERIALS & DESIGN, 2024, 244
  • [30] Microstructure evolution and mechanical properties of Al-Cu-Mn-Cd alloy fabricated by CMT-wire arc additive manufacturing
    Li, Kun
    Yang, Tianbao
    Hou, Xuru
    Ji, Chen
    Zhu, Liang
    Li, Benxiang
    Cao, Yang
    Zhao, Lin
    Ma, Chengyong
    Tian, Zhiling
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 898
12345