Effect of thermal-mechanical cycle on recovery stress of Fe-Mn-Si-Cr-Ni shape memory alloy

被引：0
|
作者：
Li, N. [1 ]
Wen, Y.H. [1 ]
Xi, H.P. [1 ]
Tu, M.J. [1 ]
Li, P.Q. [1 ]
Liu, Y.L. [1 ]
Ma, Y.L. [1 ]
机构：
[1] Dep. of Materials Shaping, Sichuan Univ., Chengdu 610065, China
来源：
Gongneng Cailiao/Journal of Functional Materials | 2000年 / 31卷 / 06期
关键词：
Deformation - Iron alloys - Quenching - Thermal effects - Thermal stress;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The effect of thermal-mechanical cycle on the recovery stress of Fe-18 Mn-5Si-8Cr-4Ni shape memory alloy has been studied. Results show that the maximum recovery stress in heating, δh, will increase as the cycle number increases, when the number is below 2. A maximum value, 156 MPa, can be attained at 2, which is 108% higher than that of specimen free of cycle. When the number is over 2, δh will decease. The recovery stress at room temperature after heating, δc, increases with the increase of cycle number. A maximum value, 255 MPa, can be attained at 3, which is 70% higher than that of specimen free of cycle; however, further increase in cycle number has little effect on δc, when the number is over 3. The recovery stress of Fe-18 Mn-5 Si-8 Cr-4 Ni shape memory alloy can be improved by the thermal-mechanical cycle.
引用
收藏
页码：601 / 602
相关论文
共 50 条
  • [41] Effect of solidification modes on the shape memory effect of cast Fe-Mn-Si-Cr-Ni shape memory alloys
    Pan, Wenhao
    Peng, Huabei
    Du, Yangyang
    Chen, Jie
    Yan, Jiazhen
    Wen, Yuhua
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 24 : 6140 - 6145
  • [42] Thermal Behavior of Mechanically Alloyed Powders Used for Producing an Fe-Mn-Si-Cr-Ni Shape Memory Alloy
    B. Pricop
    U. Söyler
    N. M. Lohan
    B. Özkal
    L. G. Bujoreanu
    D. Chicet
    C. Munteanu
    Journal of Materials Engineering and Performance, 2012, 21 : 2407 - 2416
  • [43] Thermal Behavior of Mechanically Alloyed Powders Used for Producing an Fe-Mn-Si-Cr-Ni Shape Memory Alloy
    Pricop, B.
    Soyler, U.
    Lohan, N. M.
    Ozkal, B.
    Bujoreanu, L. G.
    Chicet, D.
    Munteanu, C.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2012, 21 (11) : 2407 - 2416
  • [44] A Role of α′ Martensite Introduced by Thermo-Mechanical Treatment in Improving Shape Memory Effect of an Fe-Mn-Si-Cr-Ni Alloy
    Peng, Huabei
    Wen, Yuhua
    Liu, Gang
    Wang, Chaoping
    Li, Ning
    ADVANCED ENGINEERING MATERIALS, 2011, 13 (05) : 388 - 394
  • [45] Composition design principles for Fe-Mn-Si-Cr-Ni based alloys with better shape memory effect and higher recovery stress
    Wen, YH
    Li, N
    Xiong, LR
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 407 (1-2): : 31 - 35
  • [46] Effect of the manufacturing process on the texture and the fraction of stress-induced martensite in an Fe-Mn-Si-Cr-Ni shape memory alloy
    Druker, A. V.
    Fuster, V.
    Isola, L.
    Bolmaro, R.
    Malarria, J.
    INTERNATIONAL CONGRESS OF SCIENCE AND TECHNOLOGY OF METALLURGY AND MATERIALS, SAM - CONAMET 2014, 2015, 9 : 187 - 194
  • [47] In situ resistance analysis on transformation of constrained Fe-Mn-Si-Cr-Ni shape memory alloy
    Wen, YH
    Yan, M
    Li, N
    ACTA METALLURGICA SINICA, 2004, 40 (01) : 72 - 76
  • [48] Effect of aging time on recovery stress of Fe-Mn-Si-Cr-Ni-C shape memory alloy
    Li, Ning
    Wen, Yuhua
    Chen, Mengshi
    Tu, Mingjing
    Li, Pingquan
    Liu, Yinglai
    Ma, Yingli
    Jinshu Rechuli/Heat Treatment of Metals, 2000, (09): : 8 - 10
  • [49] Formation process of lamella structures by deformation in an Fe-Mn-Si-Cr-Ni shape memory alloy
    Kikuchi, T
    Kajiwara, S
    Tomota, Y
    JOURNAL DE PHYSIQUE IV, 1995, 5 (C8): : 445 - 450
  • [50] Analysis of wear resistance and its mechanism in an Fe-Mn-Si-Cr-Ni shape memory alloy
    Lin Chengxin
    Wang Guixin
    Wu Yandong
    Wang Jingang
    Zhang Jianjun
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 438 : 804 - 807
12345