MODELING OF GRINDING AND DEFECT FORMATION IN THE VIBRATIONAL MILL

被引：0
|
作者：
GOLDBERG, EL
ZHANAEV, ID
机构：
来源：
SIBIRSKII KHIMICHESKII ZHURNAL | 1991年 / 04期
关键词：
D O I：
暂无
中图分类号：
O6 [化学];
学科分类号：
0703 ;
摘要：
Process of grinding and formation of defects have been investigated in vibration mill with one grinding body. Run length of grinding body was proposed to use as an independent optimizing porameter for vibration mill mode. Dependence of efficiency vs relative run length has been found to have maximum. Heating of the cell, observed during milling, was proposed to be a measure of mill efficiency. Applicability of this proposal was proved experimentally in a simple case.
引用
收藏
页码：116 / 120
页数：5
相关论文
共 50 条
  • [21] SIMULATION CALCULATIONS FOR CEMENT GRINDING IN A TUBE MILL WITH UPSTREAM ROLLER GRINDING MILL
    ASSMUS, R
    REICHELT, D
    ESPIG, D
    ZEMENT-KALK-GIPS, 1993, 46 (10): : 639 - 642
  • [22] RESEARCH OF INFLUENCE OF RATIO OF VOLUMES OF GRINDING BODIES AND MATERIAL IN NEW ROTATIONAL-VIBRATIONAL MILL
    Frolov, V. S.
    Bogorodskiy, A. V.
    Blinichev, V. N.
    Vetyugov, A. V.
    IZVESTIYA VYSSHIKH UCHEBNYKH ZAVEDENII KHIMIYA I KHIMICHESKAYA TEKHNOLOGIYA, 2015, 58 (09): : 65 - +
  • [23] OPTIMAL-CONTROL OF A BALL MILL GRINDING CIRCUIT .1. GRINDING CIRCUIT MODELING AND DYNAMIC SIMULATION
    RAJAMANI, RK
    HERBST, JA
    CHEMICAL ENGINEERING SCIENCE, 1991, 46 (03) : 861 - 870
  • [24] Modeling and application of stirred mill for the coarse grinding of PGE bearing chromite ore
    Santosh, T.
    Soni, Rahul K.
    Eswaraiah, C.
    Kumar, Shravan
    Rao, D. S.
    Venugopal, R.
    SEPARATION SCIENCE AND TECHNOLOGY, 2023, 58 (01) : 149 - 163
  • [25] Modeling Based on the Extreme Learning Machine for Raw Cement Mill Grinding Process
    Lin, Xiaofeng
    Liang, Jinbo
    PROCEEDINGS OF THE 2015 CHINESE INTELLIGENT AUTOMATION CONFERENCE: INTELLIGENT TECHNOLOGY AND SYSTEMS, 2015, 338 : 129 - 138
  • [26] The Mill Load Modeling of Combined Grinding System Based on RBF Neural Networks
    Yu, Chuanjiang
    Zheng, Jianjun
    Shen, Tao
    2015 CHINESE AUTOMATION CONGRESS (CAC), 2015, : 2085 - 2090
  • [27] Analysis of Chip Formation Mechanism in Mill-grinding of SiCp/Al Composites
    Du, Jinguang
    Zhou, Liang
    Li, Jianguang
    Yao, Yingxue
    MATERIALS AND MANUFACTURING PROCESSES, 2014, 29 (11-12) : 1353 - 1360
  • [28] Raman Vibrational Properties of Carbon Nanotubes with the Radiation Defect Formation
    Dmytrenko, O. P.
    Kulish, N. P.
    Belyri, N. M.
    Lizunova, S. V.
    Prylutskyy, Yu. I.
    Valkunas, L.
    Karpicz, R.
    Shlapatskaya, V. V.
    Prilutskiy, E. V.
    Wade, T.
    Wegrowe, J. -E.
    MOLECULAR CRYSTALS AND LIQUID CRYSTALS, 2008, 497 : 370 - 377
  • [29] Analytical Modeling and Experimental Investigation of Burr Formation in Grinding
    Sudermann, H.
    Reichenbach, I. G.
    Aurich, J. C.
    BURRS - ANALYSIS, CONTROL AND REMOVAL: PROCEEDINGS OF THE CIRP INTERNATIONAL CONFERENCE ON BURRS, 2009, 2010, : 63 - 71
  • [30] ZIRCON GRINDING IN A JET MILL
    BUTYLEVA, ES
    BELOSTOTSKAYA, NS
    GLASS AND CERAMICS, 1977, 34 (1-2) : 96 - 97
12345