INFLUENCE OF HIGH INJECTION PRESSURES ON INTERNAL STRESS LEVEL IN INJECTION MOLDED SPECIMENS

被引：24
|
作者：
KUBAT, J [1 ]
RIGDAHL, M [1 ]
机构：
[1] CHALMERS UNIV TECHNOL,DIV POLYMERIC MAT,S-40220 GOTHENBURG,SWEDEN
来源：
POLYMER | 1975年 / 16卷 / 12期
关键词：
D O I：
10.1016/0032-3861(75)90215-3
中图分类号：
O63 [高分子化学（高聚物）];
学科分类号：
070305 ; 080501 ; 081704 ;
摘要：
引用
收藏
页码：925 / 929
页数：5
相关论文
共 50 条
  • [41] Influence of molding conditions on the shrinkage and roundness of injection molded parts
    Mustafa Kurt
    Yusuf Kaynak
    Omer S. Kamber
    Bilcen Mutlu
    Barkin Bakir
    Ugur Koklu
    The International Journal of Advanced Manufacturing Technology, 2010, 46 : 571 - 578
  • [42] STUDIES ON THE INFLUENCE OF THE USE OF REGRANULATES ON THE PROPERTIES OF INJECTION MOLDED PARTS
    ZIMNIAK, J
    PLASTE UND KAUTSCHUK, 1983, 30 (10): : 595 - 595
  • [43] Influence of processing on quality of injection-compression-molded disks
    Natl Taiwan Univ, Taipai, China
    Polym Eng Sci, 15 (1206-1212):
  • [44] The influence of molding conditions on molecular orientation in injection molded thermoplastics
    Daly, HB
    Sanschagrin, B
    Nguyen, KT
    Cole, K
    XIITH INTERNATIONAL CONGRESS ON RHEOLOGY, PROCEEDINGS, 1996, : 713 - 714
  • [45] INFLUENCE OF HIGH INJECTION-MOLDING PRESSURES ON ENGINEERING PROPERTIES OF LINEAR POLYETHYLENE
    DJURNER, K
    KUBAT, J
    RIGDAHL, M
    POLYMER, 1977, 18 (10) : 1068 - 1074
  • [46] Influence of molding conditions on the shrinkage and roundness of injection molded parts
    Kurt, Mustafa
    Kaynak, Yusuf
    Kamber, Omer S.
    Mutlu, Bilcen
    Bakir, Barkin
    Koklu, Ugur
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2010, 46 (5-8): : 571 - 578
  • [47] Influence of the Local Morphology on the Surface Tension of Injection Molded Polypropylene
    Gomes, M.
    Pontes, A. J.
    Viana, J. C.
    PROCEEDINGS OF PPS-29: THE 29TH INTERNATIONAL CONFERENCE OF THE POLYMER - CONFERENCE PAPERS, 2014, 1593 : 199 - 203
  • [48] Pump provides high injection pressures to engines
    Designfax Magazine, 1996, 18 (02):
  • [49] Temperature-dependent influence of molecular orientation and internal stresses on the deformation of injection-molded polypropylene parts
    Lafranche, E
    Pabiot, J
    JOURNAL OF APPLIED POLYMER SCIENCE, 1998, 68 (10) : 1661 - 1669
  • [50] Influence of matrix polymer on deformation and morphology of injection molded immiscible blends with high interfacial contact
    Li, ZM
    Yang, MB
    Huang, R
    Li, X
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2005, 44 (04) : 583 - 602
12345