Comparison of end-of-life vehicle material flows for reuse, material recycling, and energy recovery between Japan and the European Union

被引:0
|
作者
Bishal Bhari
Junya Yano
Shin-ichi Sakai
机构
[1] Kyoto University,Environment Preservation Research Center
关键词
End-of-life vehicles; Material flow analysis; Performance indicators; European Union; Japan;
D O I
暂无
中图分类号
学科分类号
摘要
Japan and the European Union (EU) both have well-established End-of-Life Vehicle (ELV) policies and management systems. However, due to the differences in these policies and management systems, the flows and indicators reflecting the performance of ELV management are not directly comparable. Hence, the study aims to understand the ELV flows of Japan and the EU, and quantitatively compare its management performances. This study uses material flow analysis to compare the ELV material flows of Japan and the EU. It quantifies the reuse, material recycling, energy recovery, and contributions of the different operations processes. Overall, it was estimated that Japan had the reuse and recycling rate of 83.7% and reuse, recycling and recovery rate of 99.5% for the year 2017, while the corresponding percentages for the EU for 2017 were 88.5% and 95.6%, respectively. Vehicles with unknown whereabouts are found to be significantly higher for the EU, while the used vehicle export fraction is significantly higher for Japan. Performance of automotive shredder residue treatment was also compared, and it was found that the EU had a lower energy recovery rate but a higher material recycling rate than Japan. Exports from ELV treatment were also studied and found to be higher for Japan.
引用
收藏
页码:644 / 663
页数:19
相关论文
共 50 条
  • [21] Energy and Raw Material Recovery from End-of-Life Tires with Pyrolysis Method in Turkey
    Arslan, Serkan
    Esmen, Cengiz
    Gunes, Mehmet
    Askin, Ferda
    5TH EURASIAN WASTE MANAGEMENT SYMPOSIUM, EWMS 2020, 2020, : 322 - 327
  • [22] Prioritizing Material Recovery for End-of-Life Printed Circuit Boards
    Wang, X.
    Gaustad, G.
    2011 IEEE INTERNATIONAL SYMPOSIUM ON SUSTAINABLE SYSTEMS AND TECHNOLOGY (ISSST), 2011,
  • [23] Prioritizing material recovery for end-of-life printed circuit boards
    Wang, Xue
    Gaustad, Gabrielle
    WASTE MANAGEMENT, 2012, 32 (10) : 1903 - 1913
  • [24] Disassembly and material recovery models for end-of-life electronics products
    Reimer, B
    Sodhi, MS
    ENVIRONMENTALLY CONSCIOUS MANUFACTURING, 2001, 4193 : 21 - 28
  • [25] Total Material Requirement of Scrap Steel from End-of-Life Vehicle
    Yamasue, Eiji
    Matsubae, Kazuyo
    Nakajima, Kenichi
    Daigo, Ichiro
    Ishihara, Keiichi N.
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2014, 100 (06): : 778 - 787
  • [26] Energy Recovery through End-of-Life Vehicles Recycling in Developing Countries
    Petronijevic, Vuk
    Dordevic, Aleksandar
    Stefanovic, Miladin
    Arsovski, Slavko
    Krivokapic, Zdravko
    Misic, Milan
    SUSTAINABILITY, 2020, 12 (21) : 1 - 26
  • [27] Recycling and Material Flow Analysis of End-of-Life Fluorescent Lamps in South Korea
    Jang, Yong-Chul
    Choi, Kyunghoon
    Kwon, Youngsun
    Song, Hakyun
    Kim, Hyunhee
    ENERGIES, 2022, 15 (23)
  • [28] Waste and material flow analysis in the end-of-life wind energy system
    Tazi, Nacef
    Kim, Junbeum
    Bouzidi, Youcef
    Chatelet, Eric
    Liu, Gang
    RESOURCES CONSERVATION AND RECYCLING, 2019, 145 : 199 - 207
  • [29] Forecasting End-of-Life Wind Turbine Material Flows in Australia under Various Wind Energy Deployment Scenarios
    Alavi, Zahraossadat
    Khalilpour, Kaveh
    Florin, Nick
    ENERGIES, 2024, 17 (04)
  • [30] Life cycle assessment on automotive bumper: Scenario analysis based on End-of-Life vehicle recycling system in Japan
    Jin, Hao
    Yu, Jeongsoo
    Okubo, Kazuaki
    WASTE MANAGEMENT & RESEARCH, 2022, 40 (06) : 765 - 774