3D Monte Carlo simulation of grain growth in friction stir welding

被引：0
|
作者：
Z. Zhang
C. P. Hu
机构：
[1] Dalian University of Technology,State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Faculty of Vehicle Engineering and Mechanics
[2] Dalian University of Technology,International Research Center for Computational Mechanics
来源：
Journal of Mechanical Science and Technology | 2018年 / 32卷
关键词：
Friction stir welding; Grain growth; Monte Carlo method; Fluid turbulence model;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The 3D fluid model was used to simulate the friction stir welding process. Three-dimensional Monte Carlo model with nucleation in each MC step was then applied to simulate the grain growth. The validity of this model is verified by comparison with the experimental and numerical results. The influences of tool shoulder diameter and rotational speed are further studied. Equiaxed grains in the stirring zone are increased with the increase of the diameter and the rotation speed of the shoulder. The grain sizes tend to be more uniform from retreating side to advancing side when the rotational speed or shoulder diameter is increased.
引用
收藏
页码：1287 / 1296
页数：9
相关论文
共 50 条
  • [41] 3D visualization of the material flow in friction stir welding process
    Zhao, Y. (zaneyanhua@hit.edu.cn), 2005, China Welding (14):
  • [42] Verification of 3D grain growth rate equations with large-scale Potts model Monte Carlo simulation
    Wang Hao
    Liu Guoquan
    Qin Xiangge
    ACTA METALLURGICA SINICA, 2008, 44 (01) : 13 - 18
  • [43] An efficient strategy for 3D numerical simulation of friction stir welding process of pure copper plates
    Constantin, M. A.
    Iordache, M. D.
    Nitu, E. L.
    Diakhate, M.
    Demmouche, Y.
    Dhondt, M.
    Badulescu, C.
    MODTECH INTERNATIONAL CONFERENCE - MODERN TECHNOLOGIES IN INDUSTRIAL ENGINEERING VIII, 2020, 916
  • [44] Error estimation and accurate mapping based ALE formulation for 3D simulation of friction stir welding
    Guerdoux, Simon
    Fourment, Lionel
    NUMIFORM '07: MATERIALS PROCESSING AND DESIGN: MODELING, SIMULATION AND APPLICATIONS, PTS I AND II, 2007, 908 : 185 - +
  • [45] Simulation of 3D material flow in friction stir welding of AA6061-T6
    Department of Engineering Mechanics, Faculty of Vehicle Engineering and Mechanics, Dalian University of Technology, Dalian 116024, China
    China Weld Eng Ed, 2008, 1 (57-63): : 57 - 63
  • [46] Simulation of 3D material flow in friction stir welding of AA6061-T6
    张昭
    张洪武
    China Welding, 2008, (01) : 57 - 63
  • [47] A 3D MONTE-CARLO (POTTS) MODEL FOR RECRYSTALLIZATION AND GRAIN GROWTH IN POLYCRYSTALLINE MATERIALS
    Ivasishin, O. M.
    Vasiliev, N. L.
    Shevchenko, S. V.
    Semiatin, S. L.
    UKRAINIAN JOURNAL OF PHYSICS, 2005, 50 (12): : 1361 - 1375
  • [48] Growth of Crystal Faces Enhanced by 3D Nuclei Deposition: A Monte Carlo Simulation
    van Enckevort, Willem J. P.
    CRYSTAL GROWTH & DESIGN, 2016, 16 (08) : 4402 - 4410
  • [49] About Abnormal Grain Growth in Joints Obtained by Friction Stir Welding
    S. Yu. Mironov
    Metal Science and Heat Treatment, 2015, 57 : 40 - 47
  • [50] About Abnormal Grain Growth in Joints Obtained by Friction Stir Welding
    Mironov, S. Yu
    METAL SCIENCE AND HEAT TREATMENT, 2015, 57 (1-2) : 40 - 47
12345