Numerical simulation and printability analysis of fused deposition modeling with dual-temperature control

被引：0
|
作者：
Xiaodan Huo
Bin Zhang
Qianglong Han
Yong Huang
Jun Yin
机构：
[1] Zhejiang University,The State Key Laboratory of Fluid Power and Mechatronic Systems, School of Mechanical Engineering
[2] Zhejiang University,Key Laboratory of 3D Printing Process and Equipment of Zhejiang Province, School of Mechanical Engineering
[3] University of Florida,Department of Mechanical and Aerospace Engineering
来源：
Bio-Design and Manufacturing | 2023年 / 6卷
关键词：
Fused deposition modeling (FDM); Dual-temperature control; Filament deposition; Printing resolution; Viscosity;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
引用
收藏
页码：174 / 188
页数：14
相关论文
共 50 条
  • [21] DUAL-TEMPERATURE MODE FOR QUANTITATIVE ANALYSIS OF GAS MIXTURES WITH MOX SENSOR
    Madrolle, S.
    Grangeat, P.
    Jutten, Ch.
    2017 ICOCS/IEEE INTERNATIONAL SYMPOSIUM ON OLFACTION AND ELECTRONIC NOSE (ISOEN 2017), 2017,
  • [22] Characterization, modeling and simulation of fused deposition modeling fabricated part surfaces
    Taufik, Mohammad
    Jain, Prashant K.
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2017, 5 (04):
  • [23] Dual-color mixing for fused deposition modeling printers
    Reiner, Tim
    Carr, Nathan
    Mech, Radomir
    St'ava, Ondrej
    Dachsbacher, Carsten
    Miller, Gavin
    COMPUTER GRAPHICS FORUM, 2014, 33 (02) : 479 - 486
  • [24] Modeling fused deposition of PLA by analysis of the layers
    Carlo, Bruni
    MATERIAL FORMING, ESAFORM 2024, 2024, 41 : 2 - 11
  • [25] Numerical Simulation of the Fused Deposition Modeling for the Manufacturing of Parts with both High Geometric Fidelity and Mechanical Quality
    Altenbach, Holm
    Janiga, Gabor
    Beiner, Mario
    Androsch, Rene
    Runge, Paul-Maximilian
    JOURNAL OF SIBERIAN FEDERAL UNIVERSITY-MATHEMATICS & PHYSICS, 2021, 14 (06): : 712 - 725
  • [26] Analysis of a dual-temperature air source heat pump cycle with an ejector
    Wang, Min
    Cheng, Yue
    Yu, Jianlin
    APPLIED THERMAL ENGINEERING, 2021, 193
  • [27] Development of a quantitative method to evaluate the printability of filaments for fused deposition modeling 3D printing
    Xu, Pengchong
    Li, Jiangwei
    Meda, Alvin
    Osei-Yeboah, Frederick
    Peterson, Matthew L.
    Repka, Michael
    Zhan, Xi
    INTERNATIONAL JOURNAL OF PHARMACEUTICS, 2020, 588
  • [28] Fused deposition modeling of polyethylene (PE): Printability assessment for low-density polyethylene and polystyrene blends
    Karaki, Ayman
    Masad, Eyad
    Khraisheh, Marwan
    Ouederni, Mabrouk
    COMPOSITES PART C: OPEN ACCESS, 2024, 15
  • [29] Performance analysis of a vapor injection linear compressor in a dual-temperature zone refrigerator
    Li, Xuan
    Zou, Huiming
    Tang, Mingsheng
    Hui, Yao
    Hu, Haitao
    INTERNATIONAL JOURNAL OF REFRIGERATION, 2024, 162 : 74 - 85
  • [30] Thermodynamic measurement and analysis of dual-temperature thermoacoustic oscillations for energy harvesting application
    Zhao, Dan
    Ji, Chenzhen
    Li, Shihuai
    Li, Junwei
    ENERGY, 2014, 65 : 517 - 526
12345