Evaluation of the total cutting force in drilling of CFRP: a novel experimental method for the analysis of the cutting mechanism

被引：11
|
作者：
Hintze W. [1 ]
Clausen R. [1 ]
Schütte C. [1 ]
Kroll K. [1 ]
机构：
[1] Hamburg University of Technology, Hamburg
来源：
Production Engineering | 2018年 / 12卷 / 3-4期
关键词：
Carbon composite; Cutting force; Drilling; Laminate; Machining;
D O I：
10.1007/s11740-018-0807-2
中图分类号：
学科分类号：
摘要：
The CFRP drilling process has not yet been fully mastered, which is due to the fact that it is not possible to measure all the cutting force components. In order to gain new insights into the drilling process, a novel experimental setup is being developed in order to record all cutting force components (cutting force, feed force, passive force). The results show that the force components are strongly dependent on the fiber cutting angle θ and the wear condition. Thereby, it will be possible to draw conclusions about the cutting mechanics in the drilling of unidirectional CFRP based on the transformation of the forces perpendicular and parallel to the fiber. © 2018, German Academic Society for Production Engineering (WGP).
引用
收藏
页码：431 / 440
页数：9
相关论文
共 50 条
  • [41] Influence of workpiece constituents and cutting speed on the cutting forces developed in the conventional drilling of CFRP composites
    Merino-Perez, Julian Luis
    Royer, Raphael
    Merson, Eleanor
    Lockwood, Aiden
    Ayvar-Soberanis, Sabino
    Marshall, Matthew B.
    COMPOSITE STRUCTURES, 2016, 140 : 621 - 629
  • [42] MEASUREMENT OF CUTTING FORCE IN TURNING AND DRILLING CASTINGS
    MOCKLI, P
    WERKSTATTSTECHNIK ZEITSCHRIFT FUR INDUSTRIELLE FERTIGUNG, 1975, 65 (12): : 725 - 732
  • [43] A novel six-state cutting force model for drilling-countersinking machining process of CFRP-Al stacks
    Cheng, Hui
    Zhang, Kaifu
    Wang, Ning
    Luo, Bin
    Meng, Qingxun
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 89 (5-8): : 2063 - 2076
  • [44] An assessment of cutting force for dental implant drilling
    Dept. of Aeronautical and Mechanical Design Engineering, Chungju National University, 50 Daehak-ro, Chungju, Chung-Buk 380-702, Korea, Republic of
    不详
    不详
    Adv. Mater. Res., (2542-2547):
  • [45] Cutting force analysis of oak for the development of a cutting force model
    Dvoracek, Ondrej
    Lechowicz, Daniel
    Haas, Franz
    Frybort, Stephan
    WOOD MATERIAL SCIENCE & ENGINEERING, 2022, 17 (06) : 771 - 782
  • [46] Towards cutting force evaluation without cutting tests
    Campocasso, S.
    Poulachon, G.
    Bissey-Breton, S.
    Costes, J. P.
    Outeiro, J. C.
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2017, 66 (01) : 77 - 80
  • [47] Cutting Force Control Applying Sensorless Cutting Force Monitoring Method
    Kurihara, Daisuke
    Kakinuma, Yasuhiro
    Katsura, Seiichiro
    JOURNAL OF ADVANCED MECHANICAL DESIGN SYSTEMS AND MANUFACTURING, 2010, 4 (05): : 955 - 965
  • [48] An experimental investigation of effect of cutting parameters on cutting zone temperature in drilling
    Delk delme şlemlernde kesme parametreler nn kesme bölgesndek sicakliǧa etks nn deneysel ncelenmes
    2013, Gazi Universitesi (28):
  • [49] AN EXPERIMENTAL INVESTIGATION OF EFFECT OF CUTTING PARAMETERS ON CUTTING ZONE TEMPERATURE IN DRILLING
    Yagmur, Selcuk
    Acir, Adem
    Seker, Ulvi
    Gunay, Mustafa
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2013, 28 (01): : 1 - 6
  • [50] Research on cutting mode and thrust force of major cutting edge for drilling CFRP composite plates based on viscoelastic mechanics and foundation beam theory
    Wang, Dong
    Yang, Qinyu
    Li, Zheng
    Tian, Shuai
    Zhu, Xiaoxiang
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 135 (5-6): : 2097 - 2116
12345