Influence of rotational speed during centrifugal casting on sliding wear behaviour of the Al-2Si alloy

被引：5
|
作者：
Mukunda P.G. [1 ]
Shailesh Rao A. [1 ]
Rao S.S. [2 ]
机构：
[1] Department of Mechanical Engineering, Nitte Meenakshi Institute of Technology, Bangalore, Karnataka
[2] Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal, Karnataka
来源：
Frontiers of Materials Science in China | 2009年 / 3卷 / 3期
关键词：
Al-Si alloy; Dry sliding wear; Rotational speed;
D O I：
10.1007/s11706-009-0052-x
中图分类号：
学科分类号：
摘要：
The microstructures and dry sliding wear behaviour of an Al-2Si alloy cast centrifugally are studied. Results indicate that at optimum speed the cast has a microstructure consisting of uniformly distributed α-Al grains and fine eutectic silicon grains. The cast exhibited better wear resistance compared to the same cast prepared at different rpms. This paper attempts to investigate the influence of the microstructural changes in the Al-2Si alloy by varying the rotational speed of the mould and its combined action on the dry sliding wear behaviour. © Higher Education Press and Springer-Verlag 2009.
引用
收藏
页码：339 / 344
页数：5
相关论文
共 50 条
  • [1] Influence of rotational speed of centrifugal casting process on appearance, microstructure, and sliding wear behaviour of Al-2Si cast alloy
    P. G. Mukunda
    Rao A. Shailesh
    Shrikantha S. Rao
    Metals and Materials International, 2010, 16 : 137 - 143
  • [2] Influence of Rotational Speed of Centrifugal Casting Process on Appearance, Microstructure, and Sliding Wear Behaviour of Al-2Si Cast Alloy
    Mukunda, P. G.
    Rao A, Shailesh
    Rao, Shrikantha S.
    METALS AND MATERIALS INTERNATIONAL, 2010, 16 (01) : 137 - 143
  • [3] Effect of Rotational Speeds on the Cast Tube During Vertical Centrifugal Casting Process on Appearance, Microstructure, and Hardness Behavior for Al-2Si Alloy
    A. Shailesh Rao
    Mahantesh S. Tattimani
    Shrikantha S. Rao
    Metallurgical and Materials Transactions B, 2015, 46 : 793 - 799
  • [4] Effect of Rotational Speeds on the Cast Tube During Vertical Centrifugal Casting Process on Appearance, Microstructure, and Hardness Behavior for Al-2Si Alloy
    Rao, A. Shailesh
    Tattimani, Mahantesh S.
    Rao, Shrikantha S.
    METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2015, 46 (02): : 793 - 799
  • [5] The influence of centrifugal forces on friction and wear in rotational sliding
    Gruetzmacher, Philipp G.
    Rosenkranz, Andreas
    Rammacher, Sebastian
    Gachot, Carsten
    Muecklich, Frank
    TRIBOLOGY INTERNATIONAL, 2017, 116 : 256 - 263
  • [6] Sliding temperature and wear behaviour of cast Al-Si base alloy
    Dwivedi, DK
    MATERIALS SCIENCE AND TECHNOLOGY, 2003, 19 (08) : 1091 - 1096
  • [7] Influence of contact area on the sliding friction and wear behaviour of an electrochemical jet textured Al-Si alloy
    Walker, J. C.
    Cinti, S.
    Kamps, T. J.
    Mitchell-Smith, J.
    Clare, A. T.
    WEAR, 2019, 426 : 1336 - 1344
  • [8] Influence of Sn content on the microstructure and dry sliding wear behaviour of hypereutectic Al-20Si alloy
    Wu, X. F.
    Zhang, G. A.
    MATERIALS AND MANUFACTURING, PTS 1 AND 2, 2011, 299-300 : 265 - +
  • [9] Optimizing the Microstructure of Al-Mg2Si In Situ Composite Made by Centrifugal Casting to Increase the Sliding Wear Resistance
    Zeinali, Ali
    Rajabi, Masoud
    Rahimipour, Mohammad Reza
    Shabani, Mohsen Ostad
    JOURNAL OF FAILURE ANALYSIS AND PREVENTION, 2023, 23 (06) : 2416 - 2438
  • [10] Optimizing the Microstructure of Al-Mg2Si In Situ Composite Made by Centrifugal Casting to Increase the Sliding Wear Resistance
    Ali Zeinali
    Masoud Rajabi
    Mohammad Reza Rahimipour
    Mohsen Ostad Shabani
    Journal of Failure Analysis and Prevention, 2023, 23 : 2416 - 2438
12345