Effect of Viscosity Measurement Method to Simulate High Pressure Die Casting of Thin-Wall AlSi10MnMg Alloy Castings

被引：1

作者：

B. W. Zhu

L. X. Li

X. Liu

L. Q. Zhang

R. Xu

机构：

[1] Hunan University,State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body

[2] Hunan University of Science and Technology,College of Mechanical and Electrical Engineering

来源：

Journal of Materials Engineering and Performance | 2015年 / 24卷

关键词：

aluminum; die cast; measurement; simulation; thin; viscosity;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

In the present study, a rotating cylinder viscometer (RCV) was adopted to measure the viscosity of AlSi10MnMg aluminum alloy. The results show that the measured viscosity is much higher than previously reported viscosity of aluminum alloys measured by oscillation vessel viscometer. The viscosity measured by RCV was introduced into the simulation of the filling progress of high pressure die casting (HPDC) for thin-walled castings of aluminum alloy (TWCA). The simulated results match well with the experimental results indicating that the RCV is the most appropriate to use for simulations of HPDC for TWCA.

引用

页码：5032 / 5036

页数：4

共 39 条

[21] The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique
Jiao, X. Y.
Zhang, W.
Liu, Y. X.
Wang, J.
Liu, W. N.
Wan, A. X.
Hu, Y. Y.
Tong, G. D.
Xiong, S. M.
[J]. MATERIALS LETTERS, 2023, 335
[22] Heat transfer behaviors between metal and die during filling process of thin-wall aluminum alloy under high pressure die casting conditions
[J]. Li, L.-X. (llxly2000@163.com), 1600, Central South University of Technology (23):
[23] Flow characteristics and solidified microstructure during filling process of thin-wall aluminum alloy under high pressure die casting conditions
[J]. Li, L.-X. (luoxing_li@yahoo.com), 1600, Central South University of Technology (24):
[24] The Effect of Vacuum Assistance on the Quality of Castings Produced by High Pressure Die Casting Method
Lagiewka, M.
Konopka, Z.
Nadolski, M.
Zyska, A.
[J]. ARCHIVES OF FOUNDRY ENGINEERING, 2014, 14 (02) : 23 - 26
[25] Effect of solution heat treatment on gas porosity and mechanical properties in a die cast step test part manufactured with a new AlSi10MnMg(Fe) secondary alloy
Niklas, A.
Orden, S.
Bakedano, A.
da Silva, M.
Nogues, E.
Fernandez-Calvo, A. I.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 667 : 376 - 382
[26] Study on the Austemperability of Thin-wall Ductile Cast Iron Produced by High-Pressure Die-casting
Hassend, Frederic van Gen
Ninnemann, Lukas
Toeberich, Felix
Breuckmann, Michael
Roettger, Arne
Weber, Sebastian
[J]. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2022, 31 (02) : 1405 - 1418
[27] Study on the Austemperability of Thin-wall Ductile Cast Iron Produced by High-Pressure Die-casting
Frederic van gen Hassend
Lukas Ninnemann
Felix Töberich
Michael Breuckmann
Arne Röttger
Sebastian Weber
[J]. Journal of Materials Engineering and Performance, 2022, 31 : 1405 - 1418
[28] Stress Analysis of Thin Wall Core Pin in Aluminum Alloy High Pressure Die Casting
Takeda, Suguru
Shinmura, Norio
Sannakanishi, Shinji
[J]. MATERIALS TRANSACTIONS, 2017, 58 (01) : 85 - 90
[29] Investigation of the Quench Sensitivity of an AlSi10Mg Alloy in Permanent Mold and High-Pressure Vacuum Die Castings
Liu, Mengyun
Zhang, Zhan
Breton, Francis
Chen, X. -Grant
[J]. MATERIALS, 2019, 12 (11):
[30] The microstructure characteristics and fracture behavior of the polyhedral primary iron-rich phase and plate-shaped eutectic iron-rich phase in a high-pressure die-cast AlSi10MnMg alloy
Jiao, X. Y.
Liu, Y. X.
Wang, J.
Liu, W. N.
Wan, A. X.
Wiesner, Stuart
Xiong, S. M.
[J]. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2023, 140 : 201 - 209

← 1 2 3 4 →