Strain weakening and superplasticity in a Bi-Sn eutectic alloy processed by high-pressure torsion

被引：7

作者：

Wang, Chuan Ting ^{[1
]}

Langdon, Terence G. ^{[1
]}

机构：

[1] Univ So Calif, Dept Aerosp & Mech Engn, Los Angeles, CA 90089 USA

来源：

6TH INTERNATIONAL CONFERENCE ON NANOMATERIALS BY SEVERE PLASTIC DEFORMATION (NANOSPD6) | 2014年 / 63卷

关键词：

EVOLUTION; BEHAVIOR; AL; DEFORMATION; HOMOGENEITY; DUCTILITY; EXAMINE;

D O I：

10.1088/1757-899X/63/1/012107

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

High-pressure torsion (HPT) was conducted on disks of a Bi-Sn eutectic alloy under a pressure of 6.0 GPa. The microstructural evolution was studied by scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Measurements of Vickers microhardness showed decreasing strength caused by strain weakening after HPT processing. Tensile testing was performed under initial strain rates from 10(-4) to 10(-2) s(-1) at room temperature. The results demonstrate a much improved elongation to failure for the Bi-Sn alloy after HPT-processing. The Bi-Sn alloy processed through 10 turns gave an elongation to failure of more than 1200% at an initial strain rate of 10(-4) s(-1) at room temperature which is significantly larger than the elongation to failure of similar to 110% in the as-cast Bi-Sn alloy under the same tensile conditions.

引用

页数：9

共 50 条

[21] Developing superplasticity in an aluminum matrix composite processed by high-pressure torsion
Sabbaghianrad, Shima
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 655 : 36 - 43
[22] An examination of microstructural evolution in a Pb-Sn eutectic alloy processed by high-pressure torsion and subsequent self-annealing
Zhang, Nian Xian
Kawasaki, Megumi
Huang, Yi
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 802
[23] An evidence of high strain rate superplasticity at intermediate homologous temperatures in an Al-Zn-Mg-Cu alloy processed by high-pressure torsion
Garcia-Infanta, J. M.
Zhilyaev, A. P.
Sharafutdinov, A.
Ruano, O. A.
Carreno, F.
JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 473 (1-2) : 163 - 166
[24] Microstructural homogeneity and superplastic behavior in an aluminum–copper eutectic alloy processed by high-pressure torsion
Megumi Kawasaki
Han-Joo Lee
Terence G. Langdon
Journal of Materials Science, 2015, 50 : 6700 - 6712
[25] Effect of Strain Rate and Temperature on Micro Fatigue Crack Propagation of Bi-Sn Eutectic Alloy
Taniguchi, Maiko
Kariya, Yoshiharu
MATERIALS TRANSACTIONS, 2016, 57 (06) : 853 - 859
[26] Significance of strain reversals in a two-phase alloy processed by high-pressure torsion
Kawasaki, Megumi
Ahn, Byungmin
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (26): : 7008 - 7016
[27] Analysis of heterogeneities in strain and microstructure in aluminum alloy and magnesium processed by high-pressure torsion
Panda, Subrata
Toth, Laszlo S.
Fundenberger, Jean-Jacques
Perroud, Olivier
Guyon, Julien
Zou, Jianxin
Grosdidier, Thierry
MATERIALS CHARACTERIZATION, 2017, 123 : 159 - 165
[28] Supercooling under crystallization of Bi-Sn eutectic alloy in contact with Bi, Sn and amorphous C
Bogatyrenko, S. I.
Minenkov, A. A.
Kryshtal, A. P.
VACUUM, 2018, 152 : 1 - 7
[29] Factors influencing superplasticity in the Ti-6Al-4V alloy Processed by high-pressure torsion
Shahmir, Hamed
Naghdi, Fariba
Pereira, Pedro Henrique R.
Huang, Yi
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 718 : 198 - 206
[30] Microstructural properties, thermal stability and superplasticity of a ZK60 Mg alloy processed by high-pressure torsion
Torbati-Sarraf, S. A.
Sabbaghianrad, S.
Langdon, T. G.
LETTERS ON MATERIALS-PIS MA O MATERIALAKH, 2015, 5 (03): : 287 - 293

← 1 2 3 4 5 →