Simulation of hot compression of Ti-Al alloy

被引：12
|
作者：
Huang, Jin-Song [1 ]
Huang, Lan [1 ]
Liu, Bin [1 ]
Zhang, Yong-Hong [1 ]
Zhang, Wei [1 ]
He, Xiao-Yu [1 ]
Liu, Yong [1 ]
机构：
[1] Cent S Univ, State Key Lab PM, Changsha 410083, Hunan, Peoples R China
来源：
INTERMETALLICS | 2007年 / 15卷 / 5-6期
关键词：
TiAl alloy; hot simulation; compression; can; macrostructure; microstructure;
D O I：
10.1016/j.intermet.2006.10.019
中图分类号：
O64 [物理化学（理论化学）、化学物理学];
学科分类号：
070304 ; 081704 ;
摘要：
Hot compressive experiments of Ti-45Al-7Nb-0.15B-0.4W (mole fraction, %) alloy canned by 45(#) carbon steel were conducted at 1050-1230 degrees C on Gleeble1500 hot simulator with nominal deformation of 30% and strain rate of 0.01 s(-1). The displacement-loading curves were obtained, and the macrostructure and microstructure were observed. The results show that the hot compressive temperature of TiAl alloy must be higher than 1050 degrees C and lower than 1230 degrees C with 45(#) steel can, and its optimum temperature is 1180 degrees C. The highest actual deformation of TiAl alloy canned by 45(#) steel is 50% with nominal deformation of 30%. The grains after being hotly compressed are flattened and elongated. (c) 2007 Published by Elsevier Ltd.
引用
收藏
页码：700 / 705
页数：6
相关论文
共 50 条
  • [11] Hot Compression Simulation of Ti3Al Alloy Based on DEFORM-3D
    Fan, Jun
    ADVANCES IN ENGINEERING DESIGN AND OPTIMIZATION II, PTS 1 AND 2, 2012, 102-102 : 240 - 244
  • [12] Development of an Al rich Ti-Al alloy with better ductility
    Mermer, Erdem
    cinici, Hanifi
    Ugur, Gokay
    Unal, Rahmi
    VACUUM, 2023, 214
  • [13] Hot corrosion behaviour of Ti-Al based intermetallics
    Zhang, K
    Li, ZW
    Gao, W
    MATERIALS LETTERS, 2002, 57 (04) : 834 - 843
  • [14] A STUDY OF MECHANICAL-BEHAVIOR OF TI-AL(SN)-LA AND TI-AL(SN)-ER ALLOY SYSTEMS
    CHI, CS
    WHANG, SH
    JOURNAL OF METALS, 1984, 36 (12): : 53 - 53
  • [15] Crystallization of sputter deposited Ti-Al amorphous alloy
    Ohnuma, M
    Abe, T
    Onodera, H
    METASTABLE PHASES AND MICROSTRUCTURES, 1996, 400 : 209 - 214
  • [16] Defect reconfiguration in a Ti-Al alloy via electroplasticity
    Zhao, Shiteng
    Zhang, Ruopeng
    Chong, Yan
    Li, Xiaoqing
    Abu-Odeh, Anas
    Rothchild, Eric
    Chrzan, Daryl C.
    Asta, Mark
    Morris, J. W., Jr.
    Minor, Andrew M.
    NATURE MATERIALS, 2021, 20 (04) : 468 - +
  • [17] Mechanistic study of hot working of a cast multi-phase near-β Ti-Al Alloy
    Hardwick, DA
    Martin, PL
    HOT WORKABILITY OF STEELS & LIGHT ALLOYS-COMPOSITES, 1996, : 237 - 244
  • [18] A mechanistic study of the hot working of cast gamma Ti-Al
    Hardwick, DA
    Martin, PL
    ADVANCES IN THE SCIENCE AND TECHNOLOGY OF TITANIUM ALLOY PROCESSING, 1996, : 153 - 160
  • [19] A study on the hot workability of a cast Ti-Al intermetallic compound
    Ha, Tae Kwon
    Jung, Jae Young
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 449 : 139 - 143
  • [20] Hot Processing Map and Hot Rolling Experiment of Ti-Al Clad Plate
    Peng Haijian
    Hu Jie
    RARE METAL MATERIALS AND ENGINEERING, 2021, 50 (12) : 4218 - 4223
12345