Tailoring parameter distributions to specific germplasm: impact on crop model-based ideotyping

被引:4
|
作者
Paleari, Livia [1 ]
Movedi, Ermes [1 ]
Vesely, Fosco Mattia [1 ]
Confalonieri, Roberto [1 ]
机构
[1] Univ Milan, ESP, Cassandra Lab, Via Celoria 2, I-20133 Milan, Italy
关键词
SENSITIVITY-ANALYSIS; GRAIN-YIELD; TRAITS; CLIMATE; WHEAT; LEAF; PERSPECTIVES; COEFFICIENTS; PERFORMANCE; GROWTH;
D O I
10.1038/s41598-019-54810-x
中图分类号
O [数理科学和化学]; P [天文学、地球科学]; Q [生物科学]; N [自然科学总论];
学科分类号
07 ; 0710 ; 09 ;
摘要
Crop models are increasingly used to identify promising ideotypes for given environmental and management conditions. However, uncertainty must be properly managed to maximize the in vivo realizability of ideotypes. We focused on the impact of adopting germplasm-specific distributions while exploring potential combinations of traits. A field experiment was conducted on 43 Italian rice varieties representative of the Italian rice germplasm, where the following traits were measured: light extinction coefficient, radiation use efficiency, specific leaf area at emergence and tillering. Data were used to derive germplasm-specific distributions, which were used to re-run a previous modelling experiment aimed at identifying optimal combinations of plant trait values. The analysis, performed using the rice model WARM and sensitivity analysis techniques, was conducted under current conditions and climate change scenarios. Results revealed that the adoption of germplasm-specific distributions may markedly affect ideotyping, especially for the identification of most promising traits. A re-ranking of some of the most relevant parameters was observed (radiation use efficiency shifted from 4th to 1st), without clear relationships between changes in rankings and differences in distributions for single traits. Ideotype profiles (i.e., values of the ideotype traits) were instead more consistent, although differences in trait values were found.
引用
收藏
页数:9
相关论文
共 50 条
  • [21] Model-based parameter identification of a fluid power component
    Manhartsgruber, B
    Mikota, J
    [J]. POWER TRANSMISSION AND MOTION CONTROL, 2002, : 229 - 244
  • [22] Fuzzy Model-Based Cutting Parameter Combination Optimization
    Horvath, R.
    Toth-Laufer, E.
    [J]. 2014 18TH INTERNATIONAL CONFERENCE ON INTELLIGENT ENGINEERING SYSTEMS (INES), 2014, : 151 - 155
  • [23] Model-based process optimization in the presence of parameter uncertainty
    Solonen, Antti
    Haario, Heikki
    [J]. ENGINEERING OPTIMIZATION, 2012, 44 (07) : 875 - 894
  • [24] Model-based experimental screening for DOC parameter estimation
    Lundberg, Bjorn
    Sjoblom, Jonas
    Johansson, Asa
    Westerberg, Bjorn
    Creaser, Derek
    [J]. COMPUTERS & CHEMICAL ENGINEERING, 2015, 74 : 144 - 157
  • [25] Model-Based MPPT Parameter Optimization for Photovoltaic Panels
    Cristaldi, Loredana
    Faller, Marco
    Laurano, Christian
    Ottoboni, Roberto
    Toscani, Sergio
    Zanoni, Michele
    [J]. 7TH INTERNATIONAL CONFERENCE ON CLEAN ELECTRICAL POWER (ICCEP 2019): RENEWABLE ENERGY RESOURCES IMPACT, 2019, : 534 - 538
  • [26] Vehicle parameter estimation using a model-based estimator
    Reina, Giulio
    Paiano, Matilde
    Blanco-Claraco, Jose-Luis
    [J]. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2017, 87 : 227 - 241
  • [27] MODEL-BASED MR PARAMETER MAPPING WITH SPARSITY CONSTRAINT
    Zhao, Bo
    Lam, Fan
    Lu, Wenmiao
    Liang, Zhi-Pei
    [J]. 2013 IEEE 10TH INTERNATIONAL SYMPOSIUM ON BIOMEDICAL IMAGING (ISBI), 2013, : 1 - 4
  • [28] A model-based approach to assist variety evaluation in sunflower crop
    Casadebaig, Pierre
    Mestries, Emmanuelle
    Debaeke, Philippe
    [J]. EUROPEAN JOURNAL OF AGRONOMY, 2016, 81 : 92 - 105
  • [29] A MODEL-BASED SYSTEM FOR CROP CLASSIFICATION FROM RADAR IMAGERY
    CONWAY, JA
    BROWN, LMJ
    VECK, NJ
    CORDEY, RA
    [J]. GEC JOURNAL OF RESEARCH, 1991, 9 (01): : 46 - 54
  • [30] Model-based optimization of crop management for climate forecast applications
    Royce, FS
    Jones, JW
    Hansen, JW
    [J]. TRANSACTIONS OF THE ASAE, 2001, 44 (05): : 1319 - 1327