Mechanomaking of high speed steel AISI M2 powders fabrication

被引：5

作者：

Matteazzi, P ^{[1
]}

Wolf, F ^{[1
]}

机构：

[1] Univ Udine, Dipartimento Sci & Tecnol Chim, I-33100 Udine, Italy

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 1998年 / 246卷 / 1-2期

关键词：

nanophase materials; high speed steels; powder metallurgy; Mossbauer spectroscopy;

D O I：

10.1016/S0921-5093(97)00748-X

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

High speed steel AISI M2 was obtained by high energy milling from the elemental powders. The kinetics of synthesis were followed by Mossbauer spectroscopy and X-ray diffraction. About 14 h are required to complete alloying (12 at.% solute content) of the matrix and formation of carbides (M6C and Fe3C) all having grain sizes below 20 nm. The mean particle size was 50 mu m and the individual particles were almost fully dense. Limited grain growth to < 100 nm at temperatures up to 1300 degrees C was observed. This new concept for the fabrication of alloys and materials is suggested to be termed mechanomaking. (C) 1998 Elsevier Science S.A. All rights reserved.

引用

页码：235 / 243

页数：9

共 50 条

[31] Effect of heat treatment on the microstructure of spray formed AISI M2 high-speed steel
Lima, RM
Jesus, ERB
Rossi, JL
ADVANCED POWDER TECHNOLOGY III, 2003, 416-4 : 95 - 99
[32] Extreme High-Speed DED of AISI M2 Steel for Coating Application and Additive Manufacturing
Ko, Min-Uh
Cuppers, Julius
Schopphoven, Thomas
Haefner, Constantin
COATINGS, 2024, 14 (08)
[33] Effect of heat treatment on the microstructure of spray formed AISI M2 high-speed steel
Lima, R.M.
Jesus, E.R.B.
Rossi, J.L.
Materials Science Forum, 2003, 416-418 (01) : 95 - 100
[34] Precipitation and decomposition behaviors of carbides in AISI M2 high-speed steel with nitrogen and mischmetal
Liu Bao-long
Lu Zhi-qing
Feng Wei-wei
Ren Ting-zhi
Fu Wan-tang
JOURNAL OF CENTRAL SOUTH UNIVERSITY, 2017, 24 (04) : 782 - 788
[35] Precipitation and decomposition behaviors of carbides in AISI M2 high-speed steel with nitrogen and mischmetal
刘宝龙
吕知清
冯唯伟
任廷志
傅万堂
JournalofCentralSouthUniversity, 2017, 24 (04) : 782 - 788
[36] Microstructure and mechanical behavior of laser surface melted AISI M2 high-speed steel
Arias, J.
Cabeza, M.
Castro, G.
Feijoo, I.
Merino, P.
Pena, G.
SURFACE AND INTERFACE ANALYSIS, 2010, 42 (6-7) : 752 - 756
[37] Solidification Microstructure of AISI M2 High Speed Steel Manufactured by the Horizontal Continuous Casting Process
Zhou, X. F.
Fang, F.
Jiang, J. Q.
INTERNATIONAL CONFERENCE ON ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, PTS ONE AND TWO, 2010, 1315 : 656 - 661
[38] Peculiarities of interface structures in AISI M2 high-speed steel in relation to carbide phases
Chaus, Alexander S.
Kryshtal, Aleksandr P.
Gruszczynski, Adam
MATERIALS SCIENCE AND TECHNOLOGY, 2024,
[39] Thermal Treatment of the AISI M2 High Speed Steel Promoted by a CO2 laser Beam
de Vasconcelos, G.
dos Reis, J. L.
Campanha, M. V.
da Silva, A. F.
ADVANCED POWDER TECHNOLOGY VI, 2008, 591-593 : 62 - +
[40] Modification of M2 cast high speed steel
Jinshu Xuebao, 3 (317):

← 1 2 3 4 5 →