Particle velocities, sizes and flux distribution in plasma spray with two powder injection ports

被引:10
|
作者
Wang, P [1 ]
Yu, SCM [1 ]
Ng, HW [1 ]
机构
[1] Nanyang Technol Univ, Sch MPE, Thermal & Fluid Res Lab, Singapore 639798, Singapore
关键词
plasma spray; yttria partially stabilized zircoma; phase Doppler anemometry; two injection ports; volume flux;
D O I
10.1016/j.msea.2004.02.037
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
A two-port powder injection scheme applied to atmospheric plasma spray (APS) was investigated using a 2-D Phase Doppler Anemometer (PDA). The 8 wt.% yttria partially stabilized zirconia (YSZ) powders were sprayed from a Miller SG-100 arc plasma torch. Radial distributions of mean particle velocities, diameter and volume flux were measured and evaluated under different combinations of plasma and carrier gas flow rates. It was found that as a result of the interaction between the powder-gas flows from the two opposite injectors, both the mean particle velocity and mean diameter distribution were more symmetrical about the centerline of the plasma torch. The volume flux distributions evaluated using PDA measurements were also compared with the actual sprayed stationary deposit. Although there existed some obvious difference between the two cases, measurements using a PDA were able to approximately predict the variation of actual deposits under different conditions. (C) 2004 Elsevier B.V. All rights reserved.
引用
收藏
页码:122 / 136
页数:15
相关论文
共 50 条
  • [32] COMPARISON OF 2 OPTICAL MEASURING METHODS FOR SIMULTANEOUS MEASUREMENT OF PARTICLE SIZES AND VELOCITIES ON ANALYSIS OF THE SPRAY CONE OF A FLAT-JET WATER NOZZLE
    FLOGEL, HH
    BAUCKHAGE, K
    CHEMIE INGENIEUR TECHNIK, 1985, 57 (04) : 360 - 361
  • [33] Modeling Particle Spray and Capture Efficiency for Direct Laser Deposition Using a Four Nozzle Powder Injection System
    Katinas, Christopher
    Shang, Weixiao
    Shin, Yung C.
    Chen, Jun
    JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2018, 140 (04):
  • [34] MODELING PARTICLE SPRAY AND CAPTURE EFFICIENCY FOR DIRECT LASER DEPOSITION USING A FOUR NOZZLE POWDER INJECTION SYSTEM
    Katinas, Christopher
    Shang, Weixiao
    Shin, Yung C.
    Chen, Jun
    PROCEEDINGS OF THE ASME 12TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE - 2017, VOL 2, 2017,
  • [35] MODELING AND PARAMETRIC ANALYSIS OF PLASMA SPRAY PARTICLE STATE DISTRIBUTION FOR DEPOSITION RATE CONTROL
    Wroblewski, Donald
    Ghosh, Onomitra
    Lum, Annie
    Willoughby, David
    VanHout, Mike
    Hogstrom, Kristina
    Basu, Soumendra N.
    Gevelber, Mike
    IMECE 2008: HEAT TRANSFER, FLUID FLOWS, AND THERMAL SYSTEMS, VOL 10, PTS A-C, 2009, : 453 - 460
  • [36] Particle slze effects on flow properties of PS304 plasma spray feedstock powder blend
    Stanford, MK
    DellaCorte, C
    Eylon, D
    27TH INTERNATIONAL COCOA BEACH CONFERENCE ON ADVANCED CERAMICS AND COMPOSITES: A, 2003, 24 (03): : 577 - 585
  • [37] Characterization of functionally graded ZrO2 thermal barrier coatings sprayed by supersonic plasma spray with dual powder feed ports
    韩志海
    王海军
    周世魁
    徐滨士
    Journal of Central South University, 2005, (S2) : 257 - 260
  • [38] Characterization of functionally graded ZrO2 thermal barrier coatings sprayed by supersonic plasma spray with dual powder feed ports
    Zhi-hai Han
    Hai-jun Wang
    Shi-kui Zhou
    Bing-shi Xu
    Journal of Central South University of Technology, 2005, 12 : 257 - 260
  • [39] Characterization of functionally graded ZrO2 thermal barrier coatings sprayed by supersonic plasma spray with dual powder feed ports
    Han, ZH
    Wang, HJ
    Zhou, SK
    Xu, BS
    JOURNAL OF CENTRAL SOUTH UNIVERSITY OF TECHNOLOGY, 2005, 12 (2): : 257 - 260
  • [40] Computational study and experimental comparison of the in-flight particle behavior for an external injection plasma spray process
    K. Remesh
    S. C. M. Yu
    H. W. Ng
    C. C. Berndt
    Journal of Thermal Spray Technology, 2003, 12 : 508 - 522