Rock Fracture Toughness Study Under Mixed Mode I/III Loading

被引:117
|
作者
Aliha, M. R. M. [1 ]
Bahmani, A. [1 ,2 ]
机构
[1] IUST, Sch Ind Engn, Welding & Joining Res Ctr, Tehran 1684613114, Iran
[2] Univ Waterloo, Dept Mech & Mechatron Engn, 200 Univ Ave West, Waterloo, ON N2L 3G1, Canada
关键词
Mixed mode I/III; Marble rock; Novel disc shape specimen; K-Ic-K-IIIc data; Fracture models; BRAZILIAN DISC SPECIMEN; II FRACTURE; BRITTLE-FRACTURE; LIMESTONE ROCK; STRAIN-ENERGY; V-NOTCHES; BEHAVIOR; STRESS; GEOMETRY; MARBLE;
D O I
10.1007/s00603-017-1201-7
中图分类号
P5 [地质学];
学科分类号
0709 ; 081803 ;
摘要
Fracture growth in underground rock structures occurs under complex stress states, which typically include the in- and out-of-plane sliding deformation of jointed rock masses before catastrophic failure. However, the lack of a comprehensive theoretical and experimental fracture toughness study for rocks under contributions of out-of plane deformations (i.e. mode III) is one of the shortcomings of this field. Therefore, in this research the mixed mode I/III fracture toughness of a typical rock material is investigated experimentally by means of a novel cracked disc specimen subjected to bend loading. It was shown that the specimen can provide full combinations of modes I and III and consequently a complete set of mixed mode I/III fracture toughness data were determined for the tested marble rock. By moving from pure mode I towards pure mode III, fracture load was increased; however, the corresponding fracture toughness value became smaller. The obtained experimental fracture toughness results were finally predicted using theoretical and empirical fracture models.
引用
收藏
页码:1739 / 1751
页数:13
相关论文
共 50 条
  • [11] Experimental and theoretical fracture toughness investigation of PUR foams under mixed mode I plus III loading
    Aliha, M. R. M.
    Linul, E.
    Bahmani, A.
    Marsavina, L.
    POLYMER TESTING, 2018, 67 : 75 - 83
  • [12] FRACTURE-TOUGHNESS OF COMPOSITE ADHEREND ADHESIVE JOINTS UNDER MIXED MODE-I AND MODE-III LOADING
    RIPLING, EJ
    SANTNER, JS
    CROSLEY, PB
    JOURNAL OF MATERIALS SCIENCE, 1983, 18 (08) : 2274 - 2282
  • [13] Fracture toughness of Ti-15Al-8Nb alloy under mixed mode I/III loading
    Paradkar, A. G.
    Kamat, S. V.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (09): : 3283 - 3288
  • [14] Investigation of blunting line and evaluation of fracture toughness under mixed mode I/III loading in commercially pure titanium
    Kamat, SV
    Srinivas, M
    MATERIALS SCIENCE AND TECHNOLOGY, 2003, 19 (01) : 62 - 66
  • [15] The effect of mixed mode I/III loading on the fracture toughness of Timetal 834 titanium alloy
    Rao, B. S. S. Chandra
    Srinivas, M.
    Kamat, S. V.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 476 (1-2): : 162 - 168
  • [16] A new fixture for fracture tests under mixed mode I/III loading
    Ayatollahi, M.R., 1600, Elsevier Ltd (51):
  • [17] Study of mixed mode fracture toughness and fracture characteristic in gypsum rock under brine saturation
    Meng, Tao
    Bao, Xiankai
    Zhao, Jinchang
    Hu, Yaoqing
    ENVIRONMENTAL EARTH SCIENCES, 2018, 77 (10)
  • [18] A new fixture for fracture tests under mixed mode I/III loading
    Ayatollahi, M. R.
    Saboori, Behnam
    EUROPEAN JOURNAL OF MECHANICS A-SOLIDS, 2015, 51 : 67 - 76
  • [19] Study of mixed mode fracture toughness and fracture characteristic in gypsum rock under brine saturation
    Tao Meng
    Xiankai Bao
    Jinchang Zhao
    Yaoqing Hu
    Environmental Earth Sciences, 2018, 77
  • [20] Mixed mode I/III fracture toughness of Armco iron
    Kamat, SV
    Srinivas, M
    Rao, PR
    ACTA MATERIALIA, 1998, 46 (14) : 4985 - 4992