Thermal Decomposition and Mechanical Properties of Polycarbonate/ABS Blends Prepared by High Shear Rate Processing

被引：3

作者：

Yoo, Jae Jung ^{[1
]}

Yong, Da Kyoung ^{[1
]}

Lee, Han Ki ^{[2
]}

Kim, Dae Sik ^{[2
]}

Lee, Hyung Ii ^{[3
]}

Kim, Sun Hong ^{[3
]}

Lee, Kee Yoon ^{[3
]}

Lee, Seung Goo ^{[1
]}

机构：

[1] Chungnam Natl Univ, Dept Adv Organ Mat & Text Syst Engn, Taejon 305764, South Korea

[2] Hyndai Motor Grp, Automot Reserch & Dev, Dept Polymer Mat Res Team, Hwaseong Si 445706, Gyeonggi Do, South Korea

[3] Chungnam Natl Univ, Dept Polymer Sci & Engn, Taejon 305764, South Korea

来源：

POLYMER-KOREA | 2014年 / 38卷 / 04期

关键词：

PC/ABS; polymer blend; high-shear; thermal decomposition; mechanical properties; PHASE MORPHOLOGY; SAN; PC;

D O I：

10.7317/pk.2014.38.4.471

中图分类号：

O63 [高分子化学（高聚物）];

学科分类号：

070305 ; 080501 ; 081704 ;

摘要：

Polycarbonate (PC) and acrylonitrile-butadiene-styrene (ABS) blends were prepared using a high shear extruder to investigate their thermal decomposition and mechanical properties with shear rate and shear time. In this experiment, high shear rate, from 1000 to 3000 rpm, in blending process was applied for 10 to 40 sec, respectively. At high shear rate over than 2000 rpm, the initial decomposition temperature was dropped significantly compared to a compounded sample because of thermal decomposition of the blend by high shear. Consequently, high shear processing gave an important effect on the mechanical and thermal properties of the PC/ABS blend. In particular, elongation of the blend decreased significantly with shear rate.

引用

页码：471 / 476

页数：6

共 50 条

[31] Effect of nanostructured fly ash on mechanical, dynamic mechanical and thermal properties of PP/ABS blends
Bonda, Sateesh
Mohanty, Smita
Nayak, Sanjay K.
IRANIAN POLYMER JOURNAL, 2015, 24 (07) : 595 - 605
[32] Effect of rubber content of ABS on properties of PC/ABS blends. 1. Rheological, mechanical, and thermal properties
Nigam, I
Nigam, D
Mathur, GN
POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2005, 44 (05) : 815 - 832
[33] Dynamic and mechanical properties of PPS/ABS blends
Lee, Y
Kim, J
Lee, M
Nam, J
Park, YH
Park, C
POLYMER-KOREA, 2002, 26 (01) : 139 - 144
[34] Rheological and mechanical properties of ABS/PC blends
Khan, MMK
Liang, RF
Gupta, RK
Agarwal, S
KOREA-AUSTRALIA RHEOLOGY JOURNAL, 2005, 17 (01) : 1 - 7
[35] Melt flow properties, mechanical properties, thermal properties and morphology of polycarbonate/highly branched polystyrene blends
Li, AJ
Chang, JY
Wang, KQ
Lu, LD
Yang, XJ
Wang, X
POLYMER INTERNATIONAL, 2006, 55 (05) : 565 - 569
[36] Morphology and thermal properties of PPS/ABS blends
Lee, Y
Kim, J
Nam, J
Park, C
Jang, S
POLYMER-KOREA, 2000, 24 (03) : 366 - 373
[37] The kinetics, thermal and mechanical properties of epoxy-polycarbonate blends cured with aromatic amine
Ming-Shin Lu
Jyh-Luen Chen
Ye-Shiu Li
Feng-Chih Chang
Ming-Shiu Li
Chen-Chi M. Ma
Journal of Polymer Research, 1998, 5 : 115 - 124
[38] Chemical reactions, thermal and mechanical properties of epoxy - polycarbonate blends cured with aromatic amines
Natl Chiao Tung Univ, Hsinchu, Taiwan
J Polym Res, 3 (177-184):
[39] Investigation on the Influence of Different Compatibilizers on Polycarbonate and High Density Polyethylene Blends: Mechanical Properties, Thermal Properties, Morphology, and Chemical Resistance
Nanjegowda, Lohith Manjunatha
Bommulu, Ramaraj
Juikar, Vishvajit
Hatna, Siddaramaiah
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH, 2013, 52 (16) : 5672 - 5682
[40] The kinetics, thermal and mechanical properties of epoxy-polycarbonate blends cured with aromatic amine
Lu, MS
Chen, JL
Li, YS
Chang, FC
Li, MS
Ma, CCM
JOURNAL OF POLYMER RESEARCH-TAIWAN, 1998, 5 (02): : 115 - 124

← 1 2 3 4 5 →