The effect of process and geometric parameters on longitudinal edge strain and product defects in cold roll forming

被引:41
|
作者
Abeyrathna, Buddhika [1 ]
Rolfe, Bernard [2 ]
Weiss, Matthias [1 ]
机构
[1] Deakin Univ, Inst Frontier Mat, Pigdons Rd, Geelong, Vic 3216, Australia
[2] Deakin Univ, Sch Engn, Pigdons Rd, Geelong, Vic 3216, Australia
基金
澳大利亚研究理事会;
关键词
Roll forming; Peak longitudinal edge strain; Longitudinal bow; Springback; Sensitivity study; High-strength steel; CHANNEL; PREDICTION; SPRINGBACK; SECTION;
D O I
10.1007/s00170-017-0164-x
中图分类号
TP [自动化技术、计算机技术];
学科分类号
0812 ;
摘要
Roll forming has been used traditionally in the construction and housing industry for the production of longitudinal components but is now increasingly applied in the automotive industry for the manufacture of structural and crash components from ultra high-strength steel (UHSS); the incremental nature of this process allows these hard-to-form materials to be shaped with higher efficiency and less shape defects than observed in common sheet forming processes such as stamping. Tight dimensional tolerances are imposed on automotive components, and this can lead to problems when roll forming UHSS where the high material strength results in shape defect and forming problems. Recent work has therefore increasingly focused on developing process monitoring and control routines for roll forming to improve process robustness and part quality. In roll forming, the longitudinal edge strain is considered to be related to product defects such as bow, twist and end flare. Process and part shape parameters have been shown to significantly influence peak longitudinal edge strain, and the link between process and product parameters, longitudinal edge strain and shape defects needs to be understood for the roll forming of UHSS if routines for process monitoring and control are to be established. Previous studies were mainly focused on traditional roll forming materials used for building products and the like. In this paper, the effect of process and part shape parameters on the peak longitudinal edge strain, longitudinal bow and springback is experimentally and statistically investigated for three different advanced high-strength steel (AHSS) and UHSS commonly used in automotive manufacturing. The results show that there are significant differences in behaviour when forming UHSS and that forming trends differ from those reported for softer steel grades. The experimental data presented in this paper should contribute to the further development of advanced process monitoring and part shape quality control routines in the roll forming AHSS and UHSS.
引用
收藏
页码:743 / 754
页数:12
相关论文
共 50 条
  • [21] Controlling the cold roll forming design process
    Mynors, D. J.
    English, M.
    Castellucci, M.
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2006, 55 (01) : 271 - 274
  • [22] Energy efficiency of cold roll forming process
    John Paralikas
    Konstantinos Salonitis
    George Chryssolouris
    The International Journal of Advanced Manufacturing Technology, 2013, 66 : 1271 - 1284
  • [23] Industrial validation of strain in cold roll forming of UHSS
    Tsang, Kwun Sing
    Ion, William
    Blackwell, Paul
    English, Martin
    PROCEEDINGS OF THE 17TH INTERNATIONAL CONFERENCE ON METAL FORMING METAL FORMING 2018, 2018, 15 : 788 - 795
  • [24] Experimental and mathematical analysis on spring-back and bowing defects in cold roll forming process
    Amin Poursafar
    Saeid Saberi
    Rasoul Tarkesh
    Meisam Vahabi
    Javad Jafari Fesharaki
    International Journal on Interactive Design and Manufacturing (IJIDeM), 2022, 16 : 531 - 543
  • [25] Experimental and mathematical analysis on spring-back and bowing defects in cold roll forming process
    Poursafar, Amin
    Saberi, Saeid
    Tarkesh, Rasoul
    Vahabi, Meisam
    Fesharaki, Javad Jafari
    INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM, 2022, 16 (02): : 531 - 543
  • [26] EFFECT OF THE FORMING PROCESS ON ADHESION IN COLD-ROLL CLAD METAL STRIP
    KNAUSCHNER, A
    TIEN, NT
    STAHL UND EISEN, 1993, 113 (07): : 81 - 85
  • [27] Effects of process parameters on forming force and accuracy in cold roll-beating forming external tooth groove
    Long Li
    Yan Li
    Mingshun Yang
    Xudong Xiao
    Limu Cui
    Fengkui Cui
    The International Journal of Advanced Manufacturing Technology, 2019, 100 : 2229 - 2242
  • [28] Effects of process parameters on forming force and accuracy in cold roll-beating forming external tooth groove
    Li, Long
    Li, Yan
    Yang, Mingshun
    Xiao, Xudong
    Cui, Limu
    Cui, Fengkui
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 100 (9-12): : 2229 - 2242
  • [29] A Simulation Study on Stress and Strain Change Rule for Channel Steel Cold Roll Forming Process
    Chen, Lin
    Wu, Chenxia
    Wang, Yan
    ADVANCED RESEARCH ON ARCHITECTONICS AND MATERIALS, 2012, 511 : 183 - 187
  • [30] COLD ROLL FORMING ROLLS UP ECONOMIES FOR PRODUCT MANUFACTURERS
    不详
    MODERN METALS, 1979, 35 (03): : 74 - &