Computer-aided design of reflector antennas: The Green Bank Radio Telescope

被引:2
|
作者
Terada, MAB [1 ]
Stutzman, WL
机构
[1] Univ Brasilia, Dept Elect Engn, Antenna Grp, BR-70919970 Brasilia, DF, Brazil
[2] Virginia Polytech Inst & State Univ, Dept Elect Engn, Antenna Lab, Blacksburg, VA 24061 USA
关键词
Green Bank Radio Telescope; low cross-polarization design algorithms; single- and dual-offset reflector configurations;
D O I
10.1109/22.661710
中图分类号
TM [电工技术]; TN [电子技术、通信技术];
学科分类号
0808 ; 0809 ;
摘要
This paper presents an evaluation of the electrical performance of the Green Bank Telescope (GET) reflector antenna [1], [2], operating as single-and dual-offset configurations, as well as a general overview of the GET system, The GET dual-offset Gregorian configuration is designed for low cross polarization (XPOL) using the dual-offset reflector antenna (DORA) synthesis package code developed by the authors [3]. The procedure implemented in DORA to upgrade an existing main reflector to a low cross-polarized dual-offset Gregorian reflector antenna is also described in this paper. All computed patterns were obtained with the parabolic reflector analysis code (PRAC) program, also developed by the authors [3], and with the commercial code GRASP7.(1) The Green Bank Telescope (GET) radiation patterns and performance values, which include original data not available anywhere else as far as the authors know, indicate that low XPOL performance can be achieved with a dual-offset configuration, provided that a low XPOL feed is used, The GET configuration is employed as a case example for the aforementioned procedure, However, an effort is made to present the main conclusions as generically as possible.
引用
收藏
页码:250 / 253
页数:4
相关论文
共 50 条
  • [21] COMPUTER-AIDED DESIGN
    TAM, CC
    ENGINEERING MATERIALS AND DESIGN, 1972, 16 (02): : 2 - &
  • [22] COMPUTER-AIDED DESIGN
    SIDERS, RA
    IEEE SPECTRUM, 1967, 4 (11) : 84 - &
  • [23] Bioprinting of Multimaterials with Computer-aided Design/Computer-aided Manufacturing
    Lee, J. M.
    Sing, S. L.
    Yeong, W. Y.
    INTERNATIONAL JOURNAL OF BIOPRINTING, 2020, 6 (01) : 65 - 73
  • [24] COMPUTER-AIDED DESIGN AND COMPUTER-AIDED MANUFACTURING OF FOOT ORTHOSES
    STAATS, TB
    KRIECHBAUM, MP
    JOURNAL OF PROSTHETICS AND ORTHOTICS, 1989, 1 (03) : 182 - 186
  • [25] EDUTECH: Computer-aided design meets computer-aided learning
    Nason, Mac
    EDUCATION AND INFORMATION TECHNOLOGIES, 2007, 12 (02) : 107 - 108
  • [26] Application of Computer-aided design and Computer-aided engineering in Hydraulic Press Design
    Gong, Guangjun
    Gao, Shoulan
    INTERNATIONAL CONFERENCE ON MECHANICAL DESIGN AND SIMULATION (MDS 2022), 2022, 12261
  • [27] To Computer-Aided Design and Manufacturing or Not to Computer-Aided Design and Manufacturing? Free Fibula Flap With Computer-Aided Technique for Mandibular Reconstruction
    Zavattero, Emanuele
    Garzino-Demo, Paolo
    Fasolis, Massimo
    Ramieri, Guglielmo
    JOURNAL OF CRANIOFACIAL SURGERY, 2015, 26 (03) : E206 - E209
  • [28] Computer-aided design/computer-aided manufacturing skull base drill
    Couldwell, William T.
    MacDonald, Joel D.
    Thomas, Charles L.
    Hansen, Bradley C.
    Lapalikar, Aniruddha
    Thakkar, Bharat
    Balaji, Alagar K.
    NEUROSURGICAL FOCUS, 2017, 42 (05)
  • [29] A performance assessment of the Green Bank Radio Telescope
    Terada, MAB
    Stutzman, WL
    1997 SBMO/IEEE MTTS-S - INTERNATIONAL MICROWAVE AND OPTOELECTRONICS CONFERENCE, PROCEEDINGS, VOLS 1 AND 2, 1997, : 571 - 576