Influence of Chip Curl on Tool-chip Contact Length in High Speed Machining

被引：4

作者：

Bi, X. F. ^{[1
]}

Sutter, G. ^{[2
]}

List, G. ^{[2
]}

Liu, Y. X. ^{[1
,2
]}

机构：

[1] Northeastern Univ, Lab Adv Mfg & Automat, PB 319, Shenyang 110004, Peoples R China

[2] Univ Paul Verlaine Metz, Mecan & Phys Mat Lab, Paulsboro, NJ USA

来源：

ADVANCES IN MATERIALS MANUFACTURING SCIENCE AND TECHNOLOGY XIII, VOL 1: ADVANCED MANUFACTURING TECHNOLOGY AND EQUIPMENT, AND MANUFACTURING SYSTEMS AND AUTOMATION | 2009年 / 626-627卷

关键词：

Tool-chip contact length; chip curl; high speed machining; uncut chip thickness; EXPERIMENTAL-VERIFICATION; ANGLE;

D O I：

10.4028/www.scientific.net/MSF.626-627.71

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The tool-chip contact length, as an important parameter controlling the geometry of tool crater wear and understanding chip formation mechanism, is widely investigated in machining The aim of this paper is to study the influence of chip curl on tool-chip contact length by means of experimental observations with high cutting speed The relationship between tool-chip contact length, chip radius of curvature and uncut chip thickness was investigated. Experimental results show the effect of increasing spiral chip radius on tool-chip contact length with low uncut chip thickness in high speed machining

引用

页码：71 / +

页数：2

共 50 条

[21] An analytical solution to cutting forces and chip thickness in machining with a grooved tool including the tool-chip contact on the tool secondary rake face
Fang, N
Wood, C
Wang, W
TRANSACTIONS OF THE NORTH AMERICAN MANUFACTURING RESEARCH INSTITUTION OF SME, VOL XXXI, 2003, 2003, : 97 - 104
[22] DETERMINATION OF PLASTIC CONTACT LENGTH BETWEEN CHIP AND TOOL IN MACHINING
WOODWARD, RL
JOURNAL OF ENGINEERING FOR INDUSTRY-TRANSACTIONS OF THE ASME, 1977, 99 (03): : 802 - 804
[23] Tribological aspects of tool-chip and tool-work contact in machining and the application of laser spectrometry
Chandrasekaran, H
Granfors, A
M'Saoubi, R
WEAR, 2006, 260 (03) : 319 - 325
[24] Calibrated thermal microscopy of the tool-chip interface in machining
Yoon, HW
Davies, MA
Burns, TJ
Kennedy, MD
THERMOSENSE XXII, 2000, 4020 : 27 - 37
[25] Machining with tool-chip contact on the tool secondary rake face - Part II: analysis and discussion
Fang, N
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2002, 44 (11) : 2355 - 2368
[26] A fractal view of tool-chip interfacial friction in machining
Raman, S
Longstreet, A
Guha, D
WEAR, 2002, 253 (11-12) : 1111 - 1120
[27] Calibrated thermal microscopy of the tool-chip interface in machining
Davies, MA
Yoon, H
Schmitz, TL
Burns, TJ
Kennedy, MD
MACHINING SCIENCE AND TECHNOLOGY, 2003, 7 (02) : 167 - 190
[28] Evaluation of methods for measuring tool-chip contact length in wet machining using different approaches (microtextured tool, in-situ visualization and restricted contact tool)
Lars Ellersiek
Christian Menze
Florian Sauer
Berend Denkena
Hans-Christian Möhring
Volker Schulze
Production Engineering, 2022, 16 : 635 - 646
[29] Evaluation of methods for measuring tool-chip contact length in wet machining using different approaches (microtextured tool, in-situ visualization and restricted contact tool)
Ellersiek, Lars
Menze, Christian
Sauer, Florian
Denkena, Berend
Moehring, Hans-Christian
Schulze, Volker
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT, 2022, 16 (05): : 635 - 646
[30] Tool-chip friction in machining with a large negative rake angle tool
Fang, N
WEAR, 2005, 258 (5-6) : 890 - 897

← 1 2 3 4 5 →