Analysis of recrystallization kinectis from microstructural evolution and micro-hardness determination

被引：0
|
作者：
Alvi, MH [1 ]
El-Dasher, BS [1 ]
Rollett, AD [1 ]
机构：
[1] Carnegie Mellon Univ, Dept Mat Sci & Engn, Pittsburgh, PA 15213 USA
来源：
HOT DEFORMATION OF ALUMINUM ALLOYS III | 2003年
关键词：
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Recrystallization kinetics of hot rolled aluminum alloy is analyzed from the indirect method of micro-hardness test and direct method of microstructural evolution using Electron Back Scattered Diffraction (EBSD) in an SEM. Isothermally annealed samples of hot rolled aluminum alloy were studied using JMAK type analysis to see if there exists any correlation between the two methods on analysis, differing in the scale of observation. A good agreement between the two methods is clearly indicated by similar numerical values of kinetics parameters from the two methods.
引用
收藏
页码：3 / 12
页数：10
相关论文
共 50 条
  • [21] Microstructural analysis, micro-hardness and wear resistance properties of quasicrystalline Al-Cu-Fe coatings on Ti-6Al-4V alloy
    Fatoba, O. S.
    Akinlabi, S. A.
    Akinlabi, E. T.
    Gharehbaghi, R.
    MATERIALS RESEARCH EXPRESS, 2018, 5 (06):
  • [22] Microstructure and Micro-Hardness of Dissimilar Metal Cladding from a Pipe-Nozzle Mockup for PWR
    Wang, Jiazhen
    Ming, Hongliang
    Zhang, Zhiming
    Chen, Jian
    Wang, Jianqiu
    COATINGS, 2022, 12 (04)
  • [23] Microstructural evolution and hardness response in the laser beam welded joints of pure titanium during recrystallization and grain growth
    Liu, H.
    Shui, J.
    Cai, T.
    Chen, Q.
    Song, X. G.
    Yang, G. J.
    MATERIALS CHARACTERIZATION, 2018, 145 : 87 - 95
  • [24] Microstructure and micro-hardness analysis of friction stir welded bi-layered laminated aluminum sheets
    Tariq M.
    Khan I.
    Hussain G.
    Farooq U.
    International Journal of Lightweight Materials and Manufacture, 2019, 2 (02) : 123 - 130
  • [25] Determination of micro-hardness and elastic modulus in the transcrystalline zone of carbon fibre/PPS composites using a knife edge indentor
    Ramanathan, T
    Schulz, E
    Subramanian, K
    COMPOSITES SCIENCE AND TECHNOLOGY, 2005, 65 (01) : 1 - 7
  • [26] Effect of the irradiance distribution from light curing units on the local micro-hardness of the surface of dental resins
    Haenel, Thomas
    Hausnerova, Berenika
    Steinhaus, Johannes
    Price, Richard B. T.
    Sullivan, Braden
    Moeginger, Bernhard
    DENTAL MATERIALS, 2015, 31 (02) : 93 - 104
  • [27] Unveiling the Microstructural Segregation and Micro-hardness Behaviour in Ti-6Al-4 V Alloy Prepared through Copper Mould Casting
    Verma, Juhi Rani
    Prabhu, Yogesh
    Jain, Abhilasha
    Bhatt, Jatin
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2024, 77 (11) : 3245 - 3253
  • [28] In-situ Monitoring on Micro-hardness of Laser Molten Zone on AISI4140 Steel by Spectral Analysis
    Wang, Siyu
    Wang, Yichen
    Liu, Changsheng
    Mazumder, Jyoti
    SCIENTIFIC REPORTS, 2020, 10 (01)
  • [29] The Analysis of Saw-tooth Chip Formation in High Speed Machining Through Material Micro-hardness Measurement
    Su, G. S.
    Liu, Z. Q.
    HIGH SPEED MACHINING, 2011, 188 : 9 - 14
  • [30] Effect of delivering light in specific narrow bandwidths from 394 to 515 nm on the micro-hardness of resin composites
    Price, Richard B. T.
    Felix, Corey A.
    DENTAL MATERIALS, 2009, 25 (07) : 899 - 908
12345