Multicriteria Optimization of Machining Parameters in WEDM of Titanium Alloy 6242

被引：3
|
作者：
Prasanna, R. [1 ]
Gopal, P. M. [1 ]
Uthayakumar, M. [2 ]
Aravind, S. [1 ]
机构：
[1] Karpagam Acad Higher Educ, Dept Mech Engn, Coimbatore 641021, Tamil Nadu, India
[2] Kalasalingam Univ, Dept Mech Engn, Krishnan Kovil 626126, Tamil Nadu, India
来源：
ADVANCES IN MANUFACTURING TECHNOLOGY | 2019年
关键词：
ANOVA; DOE; GRA; Wire cut EDM; Material removal rate; Surface roughness; Ti-6242;
D O I：
10.1007/978-981-13-6374-0_9
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This article dealswith the optimization of process parameters in WCEDM of titanium alloy (Ti-6Al-2Sn-4Zr-2Mo). Material removal rate and surface roughness were studied against the wire cut EDM process parameters, namely pulse ON time, pulse OFF time, voltage and wire feed rate. The pulse ON time selected for the experiment was 4, 5, 6 mu s, and pulse OFF time is 6, 8, 10 mu s. The voltage values selected in the experiment are 50, 65 and 85 V, while wire feed rate used was 2, 4 and 6 m/min. The effect of pulse ON, pulse OFF, voltage and wire feed rate over material removal rate and surface roughness of the machined surface is backed up with scanning electron microscopy (SEM). The contribution of parameters on responses was determined by analysis of variance, and regression models were obtained for material removal rate and surface roughness.
引用
收藏
页码：65 / 75
页数：11
相关论文
共 50 条
  • [31] WEDM of nickel based aerospace alloy: optimization of process parameters and modelling
    Kumar V.
    Jangra K.K.
    Kumar V.
    Sharma N.
    Kumar, Vinod (vinod.rohilla@outlook.com), 1600, Springer-Verlag France (11): : 917 - 929
  • [32] Multi-response optimization of WEDM parameters on machining 16MnCr5 alloy steel using Taguchi technique
    Tushar Saini
    Khushdeep Goyal
    Deepak Bhandari
    Multiscale and Multidisciplinary Modeling, Experiments and Design, 2019, 2 : 35 - 47
  • [33] Multi-Response Optimization of CNC WEDM Process Parameters for Machining Titanium alloy Ti 6Al-4V using Response Surface Methodology (RSM)
    Nandakumar, C.
    Mohan, B.
    ENGINEERING AND MANUFACTURING TECHNOLOGIES, 2014, 541-542 : 354 - +
  • [34] Simulation and optimization of machining parameters in drilling of titanium alloys
    Chatterjee, Suman
    Mahapatra, Siba Sankar
    Abhishek, Kumar
    SIMULATION MODELLING PRACTICE AND THEORY, 2016, 62 : 31 - 48
  • [35] Machining parameters in WEDM of EN31 steel using Taguchi technique optimization
    Kamalakannan, R.
    Pradeep, G. M.
    NaveenKumar, T.
    Elango, M.
    MATERIALS TODAY-PROCEEDINGS, 2022, 50 : 1781 - 1785
  • [36] An investigation on discharge servo parameters and machining servo mode optimization of MS-WEDM
    Ma, Huliang
    Wang, Yanqing
    Lv, Ming
    Yang, Shengqiang
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 116 (9-10): : 3103 - 3113
  • [37] An investigation on discharge servo parameters and machining servo mode optimization of MS-WEDM
    Huliang Ma
    Yanqing Wang
    Ming Lv
    Shengqiang Yang
    The International Journal of Advanced Manufacturing Technology, 2021, 116 : 3103 - 3113
  • [38] Optimization of wire electrical discharge machining (WEDM) process parameters using genetic algorithm
    Mahapatra, S. S.
    Patnaik, Amar
    INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2006, 13 (06) : 494 - 502
  • [39] Optimization of wire electrical discharge machining (WEDM) process parameters using Taguchi method
    Mahapatra, S. S.
    Patnaik, Amar
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2007, 34 (9-10): : 911 - 925
  • [40] Optimization of wire electrical discharge machining (WEDM) process parameters using Taguchi method
    S. S. Mahapatra
    Amar Patnaik
    The International Journal of Advanced Manufacturing Technology, 2007, 34 : 911 - 925
12345