A case study on gas assisted injection molding technology

被引：0
|
作者：
Soh, YS
机构：
来源：
ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS | 1996年 / 42卷
关键词：
D O I：
暂无
中图分类号：
TQ [化学工业];
学科分类号：
0817 ;
摘要：
Flow behavior of gas assisted injection molding process was explained with the relations between variables; resin flow length, cross section area of cavity, melt temperature, and short shot. Channel layout design concept for a television cabinet was described with the concept of spill-over, in-article spill-over, primary gas channel, unintentional gas channel, and secondary channel.
引用
收藏
页码：1006 / 1010
页数：5
相关论文
共 50 条
  • [21] Residual stresses in gas-assisted injection molding
    Custodio, Frederico J. M. F.
    Anderson, Patrick D.
    Peters, Gerrit W. M.
    Cunha, Antonio M.
    Meijer, Han E. H.
    RHEOLOGICA ACTA, 2010, 49 (01) : 23 - 44
  • [22] On the dynamics of gas-assisted injection molding process
    Chang, RY
    Tsai, MH
    Hsu, CH
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 1998, 17 (12) : 1087 - 1095
  • [23] Water and gas/water assisted injection molding of polymers
    Bociaga, Elzbieta
    POLIMERY, 2007, 52 (02) : 88 - 93
  • [24] Study on numerical simulation of cavity filling in gas-assisted injection molding
    Xin, Yong
    Ruan, Xueyu
    He, Chenghong
    Liu, Hesheng
    Yang, Guotai
    Jixie Gongcheng Xuebao/Chinese Journal of Mechanical Engineering, 2003, 39 (04): : 112 - 115
  • [25] Gas-assisted injection molding optimization with MOGA
    Urban, F
    Poloni, C
    OPTIMAIZATION IN INDUSTRY, 2002, : 149 - 161
  • [26] Water and gas/water assisted injection molding of polymers
    BociĄga, Elzbieta
    Polimery/Polymers, 2007, 52 (02): : 88 - 93
  • [27] Optimum design of gas-assisted injection molding
    Chen, CS
    Cheng, WS
    Wang, TS
    Chien, RD
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2005, 24 (15) : 1577 - 1586
  • [28] Residual stresses in gas-assisted injection molding
    Frederico J. M. F. Custódio
    Patrick D. Anderson
    Gerrit W. M. Peters
    António M. Cunha
    Han E. H. Meijer
    Rheologica Acta, 2010, 49 : 23 - 44
  • [29] Evaluation of liquid gas-assisted injection molding
    Moon, D
    Lee, S
    Kim, D
    ANTEC 2000: SOCIETY OF PLASTICS ENGINEERS TECHNICAL PAPERS, CONFERENCE PROCEEDINGS, VOLS I-III, 2000, : 3713 - 3717
  • [30] Review of Gas-assisted Injection Molding Process
    Jiang, S. F.
    Lu, C. D.
    ULTRA-PRECISION MACHINING TECHNOLOGIES, 2009, 69-70 : 645 - 648
12345