An experimental study on ejection forces of injection molding

被引：57

作者：

Sasaki, T ^{[1
]}

Koga, N ^{[1
]}

Shirai, K ^{[1
]}

Kobayashi, Y ^{[1
]}

Toyoshima, A ^{[1
]}

机构：

[1] Nihon Univ, Fac Engn, Koriyama, Fukushima 9631165, Japan

来源：

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY | 2000年 / 24卷 / 03期

关键词：

injection molding; ejection force; surface roughness; PVD coating;

D O I：

10.1016/S0141-6359(99)00039-2

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In injection molding, the ejection forces decrease when the surface roughness of mold decreases. However, the election forces increase contrary in the area of surface roughness is less than 0.2 mu mRa. Several kinds of PVD films are coated on the mold cores to prevent the increasing of ejection farces. Some of these PVD films showed effective prevention of increasing of ejection forces.

引用

页码：270 / 273

页数：4

共 50 条

[21] Ejection force modeling for stereo lithography injection molding tools
Pham, GT
Colton, JS
POLYMER ENGINEERING AND SCIENCE, 2002, 42 (04): : 681 - 693
[22] A new approach to the evaluation of ejection friction in micro injection molding
Masato, Davide
Sorgato, Marco
Lucchetta, Giovanni
JOURNAL OF MANUFACTURING PROCESSES, 2021, 62 : 28 - 36
[23] Investigation of methods used to determine ejection temperature for injection molding
Spring, M
Williams, C
ANTEC '99: PLASTICS BRIDGING THE MILLENNIA, CONFERENCE PROCEEDINGS, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPECIAL AREAS;, 1999, : 3660 - 3664
[24] EXPERIMENTAL STUDY OF SANDWICH INJECTION MOLDING OF 2 POLYMER MELTS USING SIMULTANEOUS INJECTION
WHITE, JL
LEE, BL
POLYMER ENGINEERING AND SCIENCE, 1975, 15 (07): : 481 - 485
[25] Modelling and verification of ejection forces in thermoplastic injection moulding
Bhagavatula, N
Michalski, D
Lilly, B
Glozer, G
MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING, 2004, 12 (03) : S239 - S254
[26] Experimental study of the transcription of minute width grooves by injection molding (II)
Yoshii, M
Kuramoto, H
Ochiai, Y
POLYMER ENGINEERING AND SCIENCE, 1998, 38 (09): : 1587 - 1593
[27] Statistical process control of injection molding simulation based on an experimental study
Taghizadegan, S
Harper, DO
ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS, 1996, 42 : 598 - 602
[28] Experimental Study of Injection Molding Replicability for the Micro Embossment of the Ultrasonic Vibrator
Zhu, Tieli
Liu, Ying
Yu, Tongmin
Jin, Yifei
Zhao, Danyang
POLYMERS, 2022, 14 (22)
[29] Experimental and analytical study on filling of nano structures in micro injection molding
Lin, Huang-Ya
Chang, Ching-Ho
Young, Wen-Bin
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2010, 37 (10) : 1477 - 1486
[30] EXPERIMENTAL AND THEORETICAL-STUDY OF THE INJECTION-MOLDING OF THERMOPLASTIC MATERIALS
AGASSANT, JF
ALLES, H
PHILIPON, S
VINCENT, M
POLYMER ENGINEERING AND SCIENCE, 1988, 28 (07): : 460 - 468

← 1 2 3 4 5 →