Simulation of Ironing Process for Earring Reduction In Sheet Metal Forming

被引：4

作者：

Anggono, Agus Dwi ^{[1
]}

Siswanto, Waluyo Adi ^{[2
]}

机构：

[1] Univ Muhammadiyah Surakarta, Jl A Yani POB 1 Pabelan, Sukoharjo, Jawa Tengah 57102, Indonesia

[2] Univ Tun Hussein Onn Malaysia UTHM, Fac Mech & Mfg Engn, Batu Pahat, Johor 86400, Malaysia

来源：

4TH MECHANICAL AND MANUFACTURING ENGINEERING, PTS 1 AND 2 | 2014年 / 465-466卷

关键词：

Deep drawing; ironing; FEM;

D O I：

10.4028/www.scientific.net/AMM.465-466.91

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Manufacturing of beverage cans is porcessed by using multi-stage ironing following deep drawing from the sheet material of aluminum and steel. An earing profiles are develops during deep drawing of cylindrical cup due to the planar anisotropic properties of sheet. Therefore, the analysis of earing is important to evaluate and control the development of earing. This paper describes a simulation of the cold ironing process in the forming cylinder cap. The ironing process in this study was focused on the prediction of height increasing, earing and thinning. Two different materials of aluminum AA5042 and AKDQ steel were selected for comparison. The results show that the increasing of cup height was in the same trend.

引用

页码：91 / +

页数：2

共 50 条

[1] TRIBOLOGICAL MODEL OF THE IRONING PROCESS IN SHEET METAL FORMING FOR LUBRICANTS TESTING
Adamovic, D.
Babic, M.
Stefanovic, M.
Aleksandrovic, S.
Golusija, Z.
Mitovic, S.
[J]. JOURNAL OF THE BALKAN TRIBOLOGICAL ASSOCIATION, 2010, 16 (03): : 329 - 339
[2] An analysis of ironing limit in sheet metal forming
Nam, J
Han, KS
[J]. FRACTURE AND STRENGTH OF SOLIDS, PTS 1 AND 2, 2000, 183-1 : 547 - 552
[3] Analysis of ironing limit in sheet metal forming
Nam, Jaebok
Han, Kyung Seop
[J]. Key Engineering Materials, 2000, 183
[4] PROCESS SIMULATION IN SHEET-METAL FORMING
MAKINOUCHI, A
KAWKA, M
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1994, 46 (3-4) : 291 - 307
[5] Numerical Simulation of Incremental Sheet Metal Forming Process
Ben Said, Lotfi
Wali, Mondher
Dammak, Fakhreddine
[J]. MULTIPHYSICS MODELLING AND SIMULATION FOR SYSTEMS DESIGN AND MONITORING, 2015, 2 : 489 - 496
[6] FE-simulation of a combined sheet metal forming process
Kleiner, M
Kolleck, R
Weidner, T
[J]. SIMULATION OF MATERIALS PROCESSING: THEORY, METHODS AND APPLICATIONS, 1998, : 887 - 891
[7] Meshfree method numerical simulation of sheet metal forming process
Liu Hongsheng
Yang Yuying
Li Chunfeng
[J]. 1st International Symposium on Digital Manufacture, Vols 1-3, 2006, : 815 - 819
[8] Meshfree Method Numerical Simulation of Sheet Metal Forming Process
LIU Hongsheng YANG Yuying LI Chunfeng School of Materials Science and Engineering
[J]. 武汉理工大学学报, 2006, (S3) : 815 - 819
[9] Modelling of the wall ironing process of polymer coated sheet metal
van der Aa, MAH
Schreurs, PJG
Baaijens, FPT
[J]. MECHANICS OF MATERIALS, 2001, 33 (10) : 555 - 572
[10] A FINITE-ELEMENT SIMULATION OF THE SHEET-METAL FORMING PROCESS
NAKAMACHI, E
[J]. INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING, 1988, 25 (01) : 283 - 292

← 1 2 3 4 5 →