Effect of plasma activated sintering parameters on microstructure and mechanical properties of Al-7075/B4C composites

被引：58

作者：

Wu, Chuandong ^{[1
]}

Fang, Pan ^{[1
]}

Luo, Guoqiang ^{[1
]}

Chen, Fei ^{[1
]}

Shen, Qiang ^{[1
]}

Zhang, Lianmeng ^{[1
]}

Lavernia, Enrique J. ^{[2
]}

机构：

[1] Wuhan Univ Technol, State Key Lab Adv Technol Mat Synth & Proc, Wuhan 430070, Peoples R China

[2] Univ Calif Davis, Dept Chem Engn & Mat Sci, Davis, CA 95616 USA

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2014年 / 615卷

基金：

中国国家自然科学基金;

关键词：

Plasma Activated Sintering; Al-7075/B4C Composites; Microstructure; Bending Strength; Compressive Strength; MATRIX COMPOSITES; TEMPERATURE; ALUMINUM;

D O I：

10.1016/j.jallcom.2014.06.110

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

We report on a study on the influence of Plasma activated sintering (PAS) parameters on the microstructure and mechanical properties of aluminum matrix composites (AMCs). In this paper a commercial Al alloy (7075) reinforced with 7.5 wt.% B4C were synthesized using PAS. Specifically, we studied the influence of temperature, in the range of 450 degrees C to 540 degrees C, and holding time on the densification behavior of Al-7075/B4C composites. Moreover, the influence of residual porosity on mechanical properties of Al-7075/B4C composites was established via measurements of Vickers hardness, bending and compressive strength. High mechanical properties including Vickers hardness 181.6 HV, bending strength 1100.3 MPa, high compression yield strength 878.0 MPa and fracture strength 469.3 MPa of the consolidated Al-7075/B4C composite sintered at 530 degrees C for 3 min were achieved and attributed to a fully dense microstructure and a strong interface between matrix and reinforcement. (C) 2014 Elsevier B.V. All rights reserved.

引用

页码：276 / 282

页数：7

共 50 条

[21] Microstructure and mechanical properties of B4C/2024Al functionally gradient composites
Chao, Z. L.
Wang, Z. W.
Jiang, L. T.
Chen, S. P.
Pang, B. J.
Zhang, R. W.
Du, S. Q.
Chen, G. Q.
Zhang, Q.
Wu, G. H.
MATERIALS & DESIGN, 2022, 215
[22] Synthesis of AA7075-AA7075/B4C bilayer composite with enhanced mechanical strength via plasma activated sintering
Wu, Chuandong
Wu, Jialu
Ma, Kaka
Zhang, Dalong
Xiong, Shuya
Zhang, Jian
Luo, Guoqiang
Chen, Fei
Shen, Qiang
Zhang, Lianmeng
Lavernia, Enrique J.
JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 701 : 416 - 424
[23] Effect of B4C Reinforcement Ratio and Sintering Temperature on the Mechanical Behavior in Al-B4C Composites
Pul, Muharrem
SCIENCE OF SINTERING, 2018, 50 (01) : 51 - 61
[24] The Effect of Rolling and Aging on Mechanical and Tribological Properties in B4C Particle Reinforced Al7075 Matrix Composites
Demir, Mehmet Emin
Celik, Yahya Hisman
Kalkanli, Ali
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2022, 47 (12) : 16187 - 16208
[25] The Effect of Rolling and Aging on Mechanical and Tribological Properties in B4C Particle Reinforced Al7075 Matrix Composites
Mehmet Emin Demir
Yahya Hışman Çelik
Ali Kalkanli
Arabian Journal for Science and Engineering, 2022, 47 : 16187 - 16208
[26] Effect of welding parameters and B4C contents on the microstructure and mechanical properties of friction stir welded B4C/6061Al joints
Li, Y. Z.
Wang, Q. Z.
Xiao, B. L.
Ma, Z. Y.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2018, 251 : 305 - 316
[27] Mechanical Properties and Microstructure of Reaction Sintering B4C/SiC Ceramics
Lin, W. S.
Fang, N. X.
MECHANICAL, MATERIALS AND MANUFACTURING ENGINEERING, PTS 1-3, 2011, 66-68 : 510 - +
[28] Effect of titanium on microstructure and fluidity of Al–B4C composites
Z. Zhang
K. Fortin
A. Charette
X.-G. Chen
Journal of Materials Science, 2011, 46 : 3176 - 3185
[29] Phase transformation and mechanical properties of B4C/Al composites
Zhang L.
Shi G.
Xu K.
Hao W.
Li Q.
Junyan W.
Wang Z.
Wang, Zhi (wangzhi@ujn.edu.cn), 1600, Elsevier Editora Ltda (09): : 2116 - 2126
[30] Mechanical Properties and Corrosion Kinetics of B4C/Al Composites
Zhang, Liu
Wang, Xiao
Dong, Mengqi
Qian, Qinghua
Yang, Zirun
JOM, 2025,

← 1 2 3 4 5 →