Influence of the Mg/Si Ratio on Speed Extrusion of 6XXX Alloys

被引：0

作者：

Gradoboev, Alexander ^{[1
]}

Matveeva, Irina ^{[1
]}

Ryabov, Dmitry ^{[1
]}

Vakhromov, Roman ^{[1
]}

Mann, Victor ^{[2
]}

Krokhin, Aleksandr ^{[2
]}

机构：

[1] LMTI LLC, 6-21 Leninsky Prospect, Moscow 119049, Russia

[2] UC RUSAL, Vasilisa Kozhina Str 1,Floor 2,Room 24, Moscow 121096, Russia

来源：

LIGHT METALS 2022 | 2022年

关键词：

Aluminium billets; Aluminium extrusion; High-speed extrusion; High-speed 6XXX alloys; MagnesiumSilicon ratio; MaxiFlow alloys; Anodizing response;

D O I：

10.1007/978-3-030-92529-1_45

中图分类号：

O646 [电化学、电解、磁化学];

学科分类号：

081704 ;

摘要：

Development of the building and construction and automotive industries sets the task to increase the productivity of equipment and reduce the cost of aluminium extrusion. The absolute majority among all aluminium wrought alloys for extrusion belongs to Al- Mg-Si alloys (6XXX series). The small additions of Magnesium and Silicon allow precipitation of metastable phases with Mg/Si ratio close to 1 during aging, resulting in 5 times higher strength in comparison with pure aluminium. The paper shows the evaluation of the effect of MagnesiumSilicon ratio on the extrusion speed of the developed high-speed 6XXX alloys named as MaxiFlow family. Specially developed composition and homogenization parameters of these alloys ensure the increase of extrusion speed up to 10-30% compared to the standard alloys. The study of the influence of the content of alloying and impurity elements and modes of homogenization on the phase composition of 6XXX billets is presented as well as the anodizing response.

引用

页码：322 / 328

页数：7

共 50 条

[41] Study of the crack sensitivity of 6xxx and 7xxx aluminum alloys
Nagaumi, H
Takateru, U
THERMEC'2003, PTS 1-5, 2003, 426-4 : 465 - 470
[42] Quantification of grain boundary precipitation and the influence of quench rate in 6XXX aluminum alloys
Steele, D.
Evans, D.
Nolan, P.
Lloyd, D. J.
MATERIALS CHARACTERIZATION, 2007, 58 (01) : 40 - 45
[43] Investigation on electrical conductivity and hardness of 6xxx aluminum conductor alloys with different Si levels
Khangholi, Siamak Nikzad
Javidani, Mousa
Maltais, Alexandre
Chen, X-Grant
17TH INTERNATIONAL CONFERENCE ON ALUMINIUM ALLOYS 2020 (ICAA17), 2020, 326
[44] VERIFICATION OF A FINITE-DIFFERENCE MODEL FOR THE DISSOLUTION OF AL-MG2SI EUTECTIC IN 6XXX ALUMINUM-ALLOYS
LALLI, LA
DAUER, RA
JOURNAL OF METALS, 1985, 37 (08): : A55 - A55
[45] Microstructure, tensile and bending properties of extruded Al-Mg-Si 6xxx alloys with individual and combined additions of Zr and Mn
Elasheri, Ali
Parson, Nick
Chen, X. -Grant
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 894
[46] Continuous cooling transformation diagrams for 6XXX aluminium alloys
Bryantsev, P. Yu
5TH INTERNATIONAL EEIGM/AMASE/FORGEMAT CONFERENCE ON ADVANCED MATERIALS RESEARCH, 2009, 5
[47] Revealing foundations of the intergranular corrosion of 5XXX and 6XXX Al alloys
Fan, Letian
Ma, Jijun
Zou, Chengxiong
Gao, Jun
Wang, Haisheng
Sun, Jing
Guan, Quanmei
Wang, Jun
Tang, Bin
Li, Jinshan
Wang, William Yi
MATERIALS LETTERS, 2020, 271 (271)
[48] A STUDY ON THE QUALITY OF CAST BILLETS OF 6XXX ALUMINIUM ALLOYS
Sterie, Rodica
Panait, Nicolae
Moldovan, Petru
UNIVERSITY POLITEHNICA OF BUCHAREST SCIENTIFIC BULLETIN SERIES B-CHEMISTRY AND MATERIALS SCIENCE, 2008, 70 (04): : 85 - 92
[49] Simulation of the casting and homogenization of two 6xxx series alloys
Cai, M
Robson, J
Lorimer, GW
Parson, NC
ALUMINUM ALLOYS 2002: THEIR PHYSICAL AND MECHANICAL PROPERTIES PTS 1-3, 2002, 396-4 : 209 - 214
[50] The heat treatment of rheo-high pressure die cast 6xxx series Al-Mg-Si-(Cu) alloys
Moeller, Heinrich
Daswa, Pfarelo
Govender, Gonasagren
ALUMINIUM ALLOYS 2014 - ICAA14, 2014, 794-796 : 137 - 142

← 1 2 3 4 5 →