The effect of ferrite-martensite morphology on the scratch and abrasive wear behaviour of a dual phase construction steel

被引：30
|
作者：
Xu, Xiaojun [1 ]
van der Zwaag, Sybrand [1 ]
Xu, Wei [1 ,2 ]
机构：
[1] Delft Univ Technol, Fac Aerosp Engn, Novel Aerosp Mat Grp, NL-2629 HS Delft, Netherlands
[2] Northeastern Univ, State Key Lab Rolling & Automat, Shenyang 110819, Peoples R China
来源：
WEAR | 2016年 / 348卷
关键词：
Abrasion resistance; Dual phase steels; Ferrite-martensite morphology; Scratch test; Strain hardening; Failure mechanisms; WORK-HARDENING BEHAVIOR; VOLUME FRACTION; DEFORMATION-BEHAVIOR; MICROSTRUCTURAL MORPHOLOGY; TENSILE PROPERTIES; HEAT-TREATMENT; STRENGTH; RESISTANCE; AUSTENITE; HARDNESS;
D O I：
10.1016/j.wear.2015.12.005
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
A systematic experimental investigation concerning the effect of ferrite-martensite morphology on the scratch and abrasion resistance of ferrite-martensite dual phase (DP) steels is reported. A hot rolled 22MnB5 steel was subjected to different heat treatments to generate dual phase microstructures with different ferrite-martensite morphologies. The effects of morphology on the scratch resistance and the corresponding failure mechanisms were unravelled using a multi-pass dual-indenter (MPDI) scratch test applying different load combinations. Results show that the ferrite-martensite morphology has a significant influence on scratch resistance and that the effect is contact load dependent. The scratch behaviour is linked to the strength coefficient K in the Hollomon model (sigma = K epsilon(n)) as well as the initial indentation hardness. Results suggest that the strength coefficient K corresponds well with the scratch resistance. The optimal microstructure to yield the best combination of abrasion resistance and hardness depends on the working conditions. At a low loading condition the relative ranking of the scratch resistance of the various microstructures created is in good agreement with that of the ASTM G65 abrasion test. (C) 2015 Elsevier B.V. All rights reserved.
引用
收藏
页码：148 / 157
页数：10
相关论文
共 50 条
  • [21] Effect of the intermediate quenching on fracture toughness of ferrite-martensite dual phase steels
    Sunil, B.
    Rajanna, S.
    [J]. FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY, 2021, 15 (55): : 271 - 277
  • [22] Reliability/unreliability of mixture rule in a low alloy ferrite-martensite dual phase steel
    Fereiduni, E.
    Banadkouki, S. S. Ghasemi
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2013, 577 : 351 - 359
  • [23] Effects of Heterogeneous Microstructures on the Strain Hardening Behaviors of Ferrite-Martensite Dual Phase Steel
    Ren, Chuang
    Dan, Wenjiao
    Xu, Yongsheng
    Zhang, Weigang
    [J]. METALS, 2018, 8 (10):
  • [24] Prediction of Tensile Behaviour of Ferrite-Martensite Dual Phase Steel using Real Microstructure-based RVE Simulations
    Basantia, S. K.
    Singh, V.
    Bhattacharya, A.
    Khutia, N.
    Das, D.
    [J]. MATERIALS TODAY-PROCEEDINGS, 2018, 5 (09) : 18275 - 18280
  • [25] Enhancing plasticity by increasing tempered martensite in ultra-strong ferrite-martensite dual-phase steel
    Liang, Jiangtao
    Zhao, Zhengzhi
    Guo, Baoqi
    Sun, Binhan
    Tang, Di
    [J]. MATERIALS RESEARCH EXPRESS, 2019, 6 (02)
  • [26] TENSILE STRENGTH AND DUCTILITY OF FERRITE-MARTENSITE DUAL PHASE STEELS
    Pouranvari, Majid
    [J]. METALLURGICAL & MATERIALS ENGINEERING, 2010, 16 (03) : 187 - 194
  • [27] The Role of Phase Hardness Differential on the Non-uniform Elongation of a Ferrite-Martensite Dual Phase Steel
    Soudip Basu
    Balila Nagamani Jaya
    Anirban Patra
    Sarbari Ganguly
    Monojit Dutta
    Anton Hohenwarter
    Indradev Samajdar
    [J]. Metallurgical and Materials Transactions A, 2021, 52 : 4018 - 4032
  • [28] The Role of Phase Hardness Differential on the Non-uniform Elongation of a Ferrite-Martensite Dual Phase Steel
    Basu, Soudip
    Jaya, Balila Nagamani
    Patra, Anirban
    Ganguly, Sarbari
    Dutta, Monojit
    Hohenwarter, Anton
    Samajdar, Indradev
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2021, 52 (09): : 4018 - 4032
  • [29] Microstructure failure in ferrite-martensite dual phase steel under in-situ tensile test
    Gou R.-B.
    Dan W.-J.
    Zhang W.-G.
    Yu M.
    Zhang C.-Y.
    Qiao Y.-H.
    Ma L.
    [J]. Journal of Iron and Steel Research International, 2017, 24 (3) : 350 - 356
  • [30] Electron Back Scatter Diffraction Analysis for Inhomogeneous Deformation in a Ferrite-Martensite Dual Phase Steel
    Ohtani, Shigeo
    Morikawa, Tatsuya
    Higashida, Kenji
    Hashimoto, Shun-ichi
    [J]. TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2009, 95 (08): : 620 - 627
12345