Effect of cracked blade distribution on vibration characteristics of centrifugal impeller

被引：0
|
作者：
Cheng, Gang [1 ,2 ]
Li, Jianfeng [1 ]
Wang, Weiqiang [1 ]
Sun, Jie [1 ]
机构：
[1] Shandong Univ, Key Lab High Efficiency & Clean Mech Manufacture, Sch Mech Engn, Jinan 250061, Peoples R China
[2] Shandong Jianzhu Univ, Key Lab Mech Engn & Innovat Technol, Sch Mech & Elect Engn, Jinan 250101, Peoples R China
来源：
FRONTIERS OF MECHANICAL ENGINEERING AND MATERIALS ENGINEERING II, PTS 1 AND 2 | 2014年 / 457-458卷
基金：
美国国家科学基金会;
关键词：
Centrifugal impeller; Modal analysis; Cracked blade; Finite element method; GAS-TURBINE ENGINE; FATIGUE;
D O I：
10.4028/www.scientific.net/AMM.457-458.556
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
In this paper, the finite element analysis is made to the modal analysis of the impeller, a finite element model of a impeller with cracks was established. This paper presents results of the modal of the compressor blade subjected to centrifugal force and aerodynamic equilibrium pressure. In this analysis, the numerical models without defects and also with cracks were defined. The simulation results showed that the centrifugal force due to rotational speed can greatly influence the frequency of the impeller. The distribution of two cracked blades effect the natural frequence of the impeller. When two cracked blades locate in the interval position, the increasing value of frequence is maximum. When the two cracked blades interval 150 degrees, the increasing value of frequence is minimum. It provides a basis for modal calculation of the impeller.
引用
收藏
页码：556 / 559
页数：4
相关论文
共 50 条
  • [31] DESIGN OPTIMIZATION OF SPLITTER BLADE IMPELLER IN A CENTRIFUGAL PUMP
    Takao, Shunya
    Hayashi, Kentarou
    Miyabe, Masahiro
    PROCEEDINGS OF THE ASME 2020 FLUIDS ENGINEERING DIVISION SUMMER MEETING (FEDSM2020), VOL 1, 2020,
  • [32] Blade Design Effects on the Performance of a Centrifugal Pump Impeller
    Anagnostopoulos, John S.
    COMPUTATIONAL FLUID DYNAMICS 2010, 2011, : 859 - 861
  • [33] STUDY ON BOUNDARY-LAYER OF A CENTRIFUGAL IMPELLER BLADE
    MIYAKE, Y
    OGAWA, T
    IKEMOTO, H
    BULLETIN OF THE JSME-JAPAN SOCIETY OF MECHANICAL ENGINEERS, 1975, 18 (124): : 1117 - 1125
  • [34] PERFORMANCE AND VIBRATION OF A DOUBLE VOLUTE CENTRIFUGAL PUMP - EFFECT OF IMPELLER TRIMMING
    Khalifa, Atia E.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 4A, 2015,
  • [35] Effect of number of blades and distribution of cracks on vibration localization in a cracked pre-twisted blade system
    Huang, BW
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2006, 48 (01) : 1 - 10
  • [36] Blade vibration measurement and numerical analysis of a mistuned industrial impeller in a single-stage centrifugal compressor
    Zhao, Xinwei
    Li, Hongkun
    Yang, Shuhua
    Fan, Zhenfang
    Dong, Jiannan
    Cao, Hongwei
    JOURNAL OF SOUND AND VIBRATION, 2021, 501
  • [37] Effect of Local Roughness Distribution on the Aerodynamic Performance of a Centrifugal Impeller
    Zhao, Chenxi
    Zhang, Chenqing
    Xi, Guang
    Wang, Zhiheng
    Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics, 2023, 44 (02): : 349 - 357
  • [38] Blade-to-blade flow at centrifugal impeller exit under rotating stall
    Shin, YH
    Kim, KH
    JSME INTERNATIONAL JOURNAL SERIES B-FLUIDS AND THERMAL ENGINEERING, 2003, 46 (01) : 154 - 162
  • [39] SIMULTANEOUS OPTIMIZATION OF IMPELLER BLADE LOADING DISTRIBUTION AND MERIDIONAL GEOMETRY FOR AERODYNAMIC DESIGN OF CENTRIFUGAL COMPRESSOR
    Manabe, Kaito
    Ito, Sasuga
    Furukawa, Masato
    Yamada, Kazutoyo
    Oka, Nobuhito
    Tornita, Isao
    Hayashi, Yoshihiro
    PROCEEDINGS OF THE ASME/JSME/KSME JOINT FLUIDS ENGINEERING CONFERENCE, 2019, VOL 3A, 2019,
  • [40] A BLADE-TO-BLADE SOLUTION OF THE FLOW IN A CENTRIFUGAL-COMPRESSOR IMPELLER WITH SPLITTERS
    GOULAS, A
    JOURNAL OF ENGINEERING FOR POWER-TRANSACTIONS OF THE ASME, 1980, 102 (03): : 632 - 637
12345