Optimization of Machining Parameters of Electrical Discharge Machining Tool Steel 1.2713

被引：7
|
作者：
Swiercz, Rafal [1 ]
Oniszczuk-Swiercz, Dorota [1 ]
Dabrowski, Lucjan [1 ]
Zawora, Jozef [1 ]
机构：
[1] Warsaw Univ Technol, Inst Mfg Technol, Niepodleglosci 222, PL-00663 Warsaw, Poland
来源：
XIII INTERNATIONAL CONFERENCE ELECTROMACHINING 2018 | 2018年 / 2017卷
关键词：
RSM;
D O I：
10.1063/1.5056295
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this paper, the influence of the input EDM parameters on the surface quality of tool steel 1.2713 has been modelled and optimised. Experimental studies were conducted with a design experiments (DOE) techniques. Based on the result of experimental investigation influence of EDM parameter: discharge current, time discharge and time interval on the roughness Ra and material removal rate were established using response surface methodology. Considering the properties of the EDM for the roughness Ra in the range between 1-2 mu m with the maximum possible value of the MRR process optimization was conducted based on desirability technique.
引用
收藏
页数：8
相关论文
共 50 条
  • [21] Wire electrical discharge machining of ASP30 tool steel
    Mohammad Reza Shabgard
    Ahad Gholipoor
    Mohammad Hatami
    [J]. Journal of Mechanical Science and Technology, 2016, 30 : 3799 - 3804
  • [22] Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide
    Lee, SH
    Li, XP
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 115 (03) : 344 - 358
  • [23] Machining of Inconel 718 with a defined geometry tool or by electrical discharge machining
    Badin, Vitor
    Badin, Claudia Regina Bernardi
    Machado, Alisson Rocha
    Amorim, Fred Lacerda
    [J]. JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2020, 42 (05)
  • [24] Machining of Inconel 718 with a defined geometry tool or by electrical discharge machining
    Vitor Baldin
    Claudia Regina Bernardi Baldin
    Alisson Rocha Machado
    Fred Lacerda Amorim
    [J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2020, 42
  • [25] Optimization of wire electrical discharge machining process parameters for cutting tungsten
    Rong Tai Yang
    Chorng Jyh Tzeng
    Yung Kuang Yang
    Ming Hua Hsieh
    [J]. The International Journal of Advanced Manufacturing Technology, 2012, 60 : 135 - 147
  • [26] Fuzzy inference system for modelling machining parameters in electrical discharge machining
    Rebai, S.
    Belloufi, A.
    Abdelkrim, M.
    Rezgui, I.
    Baci, I.
    Beladjal, B.
    [J]. MODTECH INTERNATIONAL CONFERENCE - MODERN TECHNOLOGIES IN INDUSTRIAL ENGINEERING VI (MODTECH 2018), 2018, 400
  • [27] Optimization Of Electrical Discharge Machining Process Parameters Using Desirability Approach
    Sengottuvel, P.
    Satishkumar, S.
    Dinakaran, D.
    [J]. ADVANCED MANUFACTURING TECHNOLOGY AND SYSTEMS, 2012, 159 : 176 - +
  • [28] Optimization of wire electrical discharge machining process parameters for cutting tungsten
    Yang, Rong Tai
    Tzeng, Chorng Jyh
    Yang, Yung Kuang
    Hsieh, Ming Hua
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2012, 60 (1-4): : 135 - 147
  • [29] Electrode Tool Wear at Electrical Discharge Machining
    Slatineanu, Laurentiu
    Schulze, Hans-Peter
    Dodun, Oana
    Coteata, Margareta
    Gherman Lorelei
    Grigoras, Irina
    [J]. MATERIAL FORMING - ESAFORM 2012, PTS 1 & 2, 2012, 504-506 : 1189 - +
  • [30] Effect of electrical discharge machining on surface characteristics and machining damage of AISI D2 tool steel
    Guu, YH
    Hocheng, H
    Chou, CY
    Deng, CS
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 358 (1-2): : 37 - 43
12345