Experimental evaluation of the Wyoming-modified two-rail shear test method for composite materials

被引：6
|
作者：
Hussain, AK [1 ]
Adams, DF
机构：
[1] Univ Teknol MARA, Shah Alam, Malaysia
[2] Univ Wyoming, Composite Mat Res Grp, Laramie, WY 82071 USA
[3] Wyoming Test Fixtures Inc, Laramie, WY USA
来源：
EXPERIMENTAL MECHANICS | 2004年 / 44卷 / 04期
关键词：
test methods; rail shear test; shear properties; composite materials;
D O I：
10.1177/0014485104044317
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In-plane unidirectional shear properties of carbon/epoxy and glass/epoxy materials were measured using unidirectional and cross-ply specimens utilizing the Wyoming-modified two-rail shear test fixture. Simple test specimens of trapezoidal and rectangular geometries, and specimens with tabs were tested. Various specimen aspect ratios were also considered. Untabbed unidirectional specimens exhibited premature shear failures but cross-ply specimens produced reasonably reliable results with acceptable failure modes. Both bonded tab and integral tab 00 specimens were found to give comparable results. Unidirectional and cross-ply PEEK specimens, and angle-ply and quasi-isotropic AS4/3501-6 specimens, were also tested.
引用
下载
收藏
页码：354 / 364
页数：11
相关论文
共 36 条
  • [21] THE IOSIPESCU SHEAR TEST METHOD AS USED FOR TESTING POLYMERS AND COMPOSITE-MATERIALS
    ADAMS, DF
    POLYMER COMPOSITES, 1990, 11 (05) : 286 - 290
  • [22] Shear test method for and mechanical characteristics of short basalt fiber reinforced polymer composite materials
    Chen, Jinxiang
    Tuo, Wanyong
    Wan, Chunfeng
    Zhang, Xiaoming
    JOURNAL OF APPLIED POLYMER SCIENCE, 2018, 135 (16)
  • [23] Experimental and numerical investigation of the effects of porosity on the in-plane shear properties of CFRPs using the V-notched rail shear test method
    A. G. Stamopoulos
    A. P. Psaropoulos
    K. Tserpes
    International Journal of Material Forming, 2021, 14 : 67 - 82
  • [24] Experimental and numerical investigation of the effects of porosity on the in-plane shear properties of CFRPs using the V-notched rail shear test method
    Stamopoulos, A. G.
    Psaropoulos, A. P.
    Tserpes, K.
    INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2021, 14 (01) : 67 - 82
  • [25] EVALUATION OF INPLANE SHEAR TEST METHODS FOR ADVANCED COMPOSITE-MATERIALS BY THE DECISION-ANALYSIS TECHNIQUE
    LEE, S
    MUNRO, M
    COMPOSITES, 1986, 17 (01): : 13 - 22
  • [26] DETERMINATION OF THE COMPLEX SHEAR MODULUS OF DAMPING MATERIALS BY THE COMPOSITE BEAM TEST METHOD - (AN EVALUATION OF DETERMINED VALUES IN CONSIDERATION OF EFFECT OF BONDING ADHESIVE LAYER)
    DEWA, H
    JSME INTERNATIONAL JOURNAL SERIES A-MECHANICS AND MATERIAL ENGINEERING, 1994, 37 (01): : 43 - 51
  • [27] EVALUATION OF MODE II FRACTURE TOUGHNESS IN GLASS CLOTH/ EPOXY LAMINATES BY RAIL-SHEAR TEST METHOD.
    Kawada, Hiroyuki
    Aoki, Toshio
    Kondoh, Monta
    Hayashi, Ikuhiko
    Zairyo/Journal of the Society of Materials Science, Japan, 1988, 37 (417) : 683 - 689
  • [28] A SYMMETRIC RAIL SHEAR TEST FOR MODE-II FRACTURE-TOUGHNESS (GIIC) OF COMPOSITE-MATERIALS - FINITE-ELEMENT ANALYSIS
    LAKSHMINARAYANA, HV
    JOURNAL OF COMPOSITE MATERIALS, 1984, 18 (03) : 227 - 238
  • [29] Evaluation of Interfacial Fracture Toughness and Interfacial Shear Strength of Typha Spp. Fiber/Polymer Composite by Double Shear Test Method
    Ikramullah
    Rizal, Samsul
    Nakai, Yoshikazu
    Shiozawa, Daiki
    Khalil, H. P. S. Abdul
    Huzni, Syifaul
    Thalib, Sulaiman
    MATERIALS, 2019, 12 (14)
  • [30] EFFICIENCY OF THE NEEDLE PROBE TEST FOR EVALUATION OF THERMAL CONDUCTIVITY OF COMPOSITE MATERIALS: TWO-SCALE ANALYSIS
    Lydzba, Dariusz
    Rozanski, Adrian
    Rajczakowska, Magdalena
    Stefaniuk, Damian
    STUDIA GEOTECHNICA ET MECHANICA, 2014, 36 (01) : 55 - 62
1234