On-line self-tuning using embedded pressure sensors in the injection molding process

被引：0

作者：

Luo, RC ^{[1
]}

Chen, YS ^{[1
]}

Hua, CC ^{[1
]}

Chen, HC ^{[1
]}

机构：

[1] Natl Chung Cheng Univ, Dept Elect Engn, Chiayi 621, Taiwan

来源：

IECON 2000: 26TH ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY, VOLS 1-4: 21ST CENTURY TECHNOLOGIES AND INDUSTRIAL OPPORTUNITIES | 2000年

关键词：

D O I：

暂无

中图分类号：

TP [自动化技术、计算机技术];

学科分类号：

0812 ;

摘要：

Automatic tuning of control parameters inside the on-line pressure feedback data in the mold can ensure high-quality of the injection molding product. This paper presents an algorithm to estimate the pressure distribution on-line by using measurement data from pressure sensors embedded in the nozzle and cavity during the injection molding process. According to the estimated pressure distribution around the mold, necessary control parameters can be calculated for automatic tuning of the injection molding. ne experimental results of the holding phase in injection-molding process demonstrate clearly accuracy of the proposed method.

引用

页码：1068 / 1073

页数：6

共 50 条

[31] Self-tuning chemical sensors for molten metals
Kumar, R. Vasant
Fray, Derek J.
SOHN INTERNATIONAL SYMPOSIUM ADVANCED PROCESSING OF METALS AND MATERIALS, VOL 3: THERMO AND PHYSICOCHEMICAL PRINCIPLES: SPECIAL MATERIALS AND AQUEOUS AND ELECTROCHEMICAL PROCESSING, 2006, : 609 - +
[32] On-line measurement device for viscosity of polymer melt during injection molding process
Zhang J.-F.
Zhao P.
Zhou H.-W.
Fu J.-Z.
Chen Z.-C.
Zhao, Peng (pengzhao@zju.edu.cn), 1600, Zhejiang University (54): : 1474 - 1480
[33] Development of device for on-line monitoring cavity information during injection molding process
Zhao, P. (pengzhao@zju.edu.cn), 1600, Huazhong University of Science and Technology (42):
[34] On-line self-tuning controller for induction motor based on generalized minimum variance method
Yaacob, S
Mohamed, FA
SICE '98 - PROCEEDINGS OF THE 37TH SICE ANNUAL CONFERENCE: INTERNATIONAL SESSION PAPERS, 1998, : 875 - 878
[35] On-line self-tuning of PI controller for PMSM drives based on the iterative learning control
Yang, M
Gao, Y
Xu, DG
Yu, Y
APEC 2005: TWENTIETH ANNUAL IEEE APPLIED POWER ELECTRONICS CONFERENCE AND EXPOSITION, VOLS 1-3, 2005, : 1889 - 1893
[36] On-line self-tuning ANN-based speed control of a PM DC motor
Rahman, MA
Hoque, MA
IEEE-ASME TRANSACTIONS ON MECHATRONICS, 1997, 2 (03) : 169 - 178
[37] A DSP-based fully digital PMSM servo drive using on-line self-tuning PI controller
Zhang, B
Li, YH
Zuo, YS
IPEMC 2000: THIRD INTERNATIONAL POWER ELECTRONICS AND MOTION CONTROL CONFERENCE, VOLS 1-3, PROCEEDINGS, 2000, : 1012 - 1017
[38] A process monitoring and control system for injection molding using nozzle-based pressure and temperature sensors
Orzechowski, S
Paris, A
Dobbin, CJB
CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 : 424 - 430
[39] Self-tuning porous silicon chemitransistor gas sensors
Lazzerini, Giovanni Mattia
Strambini, Lucanos Marsilio
Barillaro, Giuseppe
2013 IEEE SENSORS, 2013, : 963 - 966
[40] Thin film PZT pressure/temperature sensory arrays for on-line monitoring of injection molding
Luo, RC
Tsai, CS
IECON'01: 27TH ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY, VOLS 1-3, 2001, : 375 - 380

← 1 2 3 4 5 →