Wear Behavior of Mg Alloy Procduced by Equal Channel Angular Extrusion

被引：1
|
作者：
Gao, Leilei [1 ]
Zhang, Jinzhong [1 ]
机构：
[1] China Univ Petr, Sch Mech & Elect Engn, Qingdao 266580, Shandong, Peoples R China
来源：
RESOURCES AND SUSTAINABLE DEVELOPMENT, PTS 1-4 | 2013年 / 734-737卷
关键词：
ECAE; Mg alloy; wear behavior; mechanical properties; AZ31 MAGNESIUM ALLOY; MECHANICAL-PROPERTIES; ECAE; MICROSTRUCTURES;
D O I：
10.4028/www.scientific.net/AMR.734-737.2369
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A commercial Mg alloy was prepared through equal channel angular extrusion (ECAE) process. The effect of ECAE on mechanical and tribological properties of the alloy was investigated. Experimental results showed that the hardness and strength of the alloy with ECAE were higher than that of the alloy without ECAE and increased with the increase pass number. The friction coefficient and wear resistance of the alloy after ECAE were significantly improved.
引用
收藏
页码：2369 / 2372
页数：4
相关论文
共 50 条
  • [41] Microstructure, texture and mechanical properties of AZ31 Mg alloy produced by equal channel angular extrusion
    Department of Materials Engineering, McGill University, Montreal, QC, Canada
    不详
    不详
    Can Metall Q, 2008, 4 (437-448):
  • [42] Effect of second phase on the mechanical properties of Mg-Al-Zn alloy by equal channel angular extrusion
    Ding, Wenjiang
    Jin, Li
    Lin, Dongliang
    Zeng, Xiaoqin
    Mao, Dali
    2006 BIMW: 2006 BEIJING INTERNATIONAL MATERIALS WEEK, PTS 1-4: MAGNESIUM, 2007, 546-549 : 249 - +
  • [43] Microstructure, crystallographic texture, and plastic anisotropy evolution in an Mg alloy during equal channel angular extrusion processing
    Al-Maharbi, Majid
    Karaman, Ibrahim
    Beyerlein, Irene J.
    Foley, David
    Hartwig, K. Ted
    Kecskes, Laszlo J.
    Mathaudhu, Suveen N.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (25-26): : 7616 - 7627
  • [44] TEM studies on recovery and recrystallisation in Equal Channel Angular Extrusion processed Al-3%Mg alloy
    S. Giribaskar
    R. Gouthama
    J. Prasad
    Transactions of the Indian Institute of Metals, 2008, 61 : 173 - 176
  • [45] Achieving high strain rate superplasticity in an At-Li-Mg alloy through equal channel angular extrusion
    Kaibyshev, R
    Shipilova, K
    Musin, F
    Motohashi, Y
    MATERIALS SCIENCE AND TECHNOLOGY, 2005, 21 (04) : 408 - 418
  • [46] Microstructural evolution of Al-Mg-Er-Zr alloy by equal channel angular extrusion at room temperature
    Xue, Da
    Wei, Wu
    Wen, Shengping
    Wu, Xiaolan
    Shi, Wei
    Zhou, Xiaorong
    Gao, Kunyuan
    Huang, Hui
    Nie, Zuoren
    MATERIALS LETTERS, 2023, 334
  • [47] TEM Studies On Recovery And Recrystallisation In Equal Channel Angular Extrusion Processed Al-3% Mg Alloy
    Giribaskar, S.
    Gouthama
    Prasad, R.
    Ramkumar, J.
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2008, 61 (2-3) : 173 - 176
  • [48] Microstructural characterization of an extruded Mg-Ni-Y-RE alloy processed by equal channel angular extrusion
    Eddahbi, M.
    Perez, P.
    Monge, M. A.
    Garces, G.
    Pareja, R.
    Adeva, P.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 473 (1-2) : 79 - 86
  • [49] Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy
    Wang, Xi-Shu
    Jin, Li
    Li, Ying
    Guo, Xing-Wu
    MATERIALS LETTERS, 2008, 62 (12-13) : 1856 - 1858
  • [50] Deformation behavior and strain homogeneity in equal channel angular extrusion/pressing
    Nagasekhar, An.
    Tick-Hon, Yip
    Seow, H. P.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 192 : 449 - 452
12345