Structural optimization and hydraulic performance analysis of bionic pit flow channels based on a genetic algorithm

被引:3
|
作者
Xu, Tianyu [1 ]
Su, Yanru [1 ]
Su, Zhouming [1 ]
Zhi, Shuteng [1 ]
Zheng, Ennan [1 ]
机构
[1] Heilongjiang Univ, Sch Hydraul & Elect Power, Harbin 150080, Peoples R China
关键词
D O I
10.1038/s41598-022-26569-1
中图分类号
O [数理科学和化学]; P [天文学、地球科学]; Q [生物科学]; N [自然科学总论];
学科分类号
07 ; 0710 ; 09 ;
摘要
Orthogonal experiments have mostly been used in the structural optimization of drip irrigation emitter flow channels. To further improve the efficiency of the optimal design, this study used a genetic algorithm to optimize the structure of the bionic pit flow channel. Based on the structural similarity and performance optimization of the torus-margo bordered pit structure, the constitutive equation of the flow channel unit was constructed. The selection, crossover and mutation operators were set by the genetic algorithm, and the objective function value was calculated. The design variables and known variables that met the requirements were put into the computational domain model, and the pit flow channel structure was simulated and optimized. The results showed that there were large low-velocity regions at the junctions and corners of the pit flow channel units at a working pressure of 50 kPa, and no complete low-velocity vortices were observed, indicating that the flow channels had good anti-clogging performance. The distribution of flow velocity on the same cross-section was quite different, which made the flow layers collide and mix, which intensified the loss of energy, indicating that it had a good energy dissipation effect. The multivariate linear regression analysis showed that the four variables of tooth stagger value (j), flow channel angle (theta), tooth spacing (l) and inner and outer boundary spacing (h) had a decreasing degree of influence on the flow index (x). The flow index (x) was negatively correlated with the tooth stagger value (j), flow channel angle (theta) and tooth spacing (l), and positively correlated with the inner and outer boundary spacing (h). The test results of physical samples showed that the average error between the simulation results and the real values was 3.4%, indicating that the accuracy was high, which can provide a basis for the structural optimization design of related pit drip irrigation emitters.
引用
收藏
页数:12
相关论文
共 50 条
  • [31] Optimization of polymer electrolyte membrane fuel cell flow channels using a genetic algorithm
    Center for Fuel Cell Research, Department of Mechanical Engineering, University of Delaware, Newark, DE 19716, United States
    J Power Sources, 22 (9407-9418):
  • [32] Optimization of polymer electrolyte membrane fuel cell flow channels using a genetic algorithm
    Catlin, Glenn
    Advani, Suresh G.
    Prasad, Ajay K.
    JOURNAL OF POWER SOURCES, 2011, 196 (22) : 9407 - 9418
  • [33] Genetic algorithm for the design of structural optimization
    Harbin Jianzhu Daxue Xuebao, 4 (18-23):
  • [34] A robust genetic algorithm for structural optimization
    Chen, SY
    Rajan, SD
    STRUCTURAL ENGINEERING AND MECHANICS, 2000, 10 (04) : 313 - 336
  • [35] DISTRIBUTED GENETIC ALGORITHM FOR STRUCTURAL OPTIMIZATION
    ADELI, H
    KUMAR, S
    JOURNAL OF AEROSPACE ENGINEERING, 1995, 8 (03) : 156 - 163
  • [36] Evolutionary Algorithm Based Structural Optimization for Patch Antenna Design and its Performance Analysis
    Sudhakaran, Gopika
    Kandipati, Bindu
    Surya, Bhuvan G.
    Shree, V. Karthikhaa
    Sivaprasad, M.
    Jayakumar, M.
    2017 INTERNATIONAL CONFERENCE ON ADVANCES IN COMPUTING, COMMUNICATIONS AND INFORMATICS (ICACCI), 2017, : 2189 - 2192
  • [37] Performance Analysis of Clustering Based Genetic Algorithm
    Najeeb, Athaur Rahman
    Aibinu, A. M.
    Nwohu, M. N.
    Salami, M. J. E.
    Salau, H. Bello
    PROCEEDINGS OF 6TH INTERNATIONAL CONFERENCE ON COMPUTER AND COMMUNICATION ENGINEERING (ICCCE 2016), 2016, : 327 - 331
  • [38] Bionic Design and Optimization on the Flow Channel of a Legged Robot Joint Hydraulic Drive Unit Based on Additive Manufacturing
    Huang, Zhipeng
    Du, Chenhao
    Wang, Chenxu
    Sun, Qianran
    Xu, Yuepeng
    Shao, Lufang
    Yu, Bin
    Ma, Guoliang
    Kong, Xiangdong
    BIOMIMETICS, 2024, 9 (01)
  • [39] Optimization Performance Analysis for Adaptive Genetic Algorithm with Nonlinear Probabilities
    Sun, Wenjuan
    Su, Qiaoping
    Yuan, Hongli
    Chen, Yan
    INTERNATIONAL JOURNAL OF ADVANCED COMPUTER SCIENCE AND APPLICATIONS, 2022, 13 (06) : 361 - 366
  • [40] RETRACTED: Analysis of image processing algorithm based on bionic intelligent optimization (Retracted Article)
    Du, Yuetao
    Yang, Nana
    CLUSTER COMPUTING-THE JOURNAL OF NETWORKS SOFTWARE TOOLS AND APPLICATIONS, 2019, 22 (02): : S3505 - S3512