Application of X-ray microtomography to study the influence of the casting microstructure upon the tensile behaviour of an Al-Si alloy

被引：32

作者：

Limodin, Nathalie ^{[1
]}

El Bartali, Ahmed ^{[1
,2
]}

Wang, Long ^{[1
,2
]}

Lachambre, Joel ^{[3
]}

Buffiere, Jean-Yves ^{[3
]}

Charkaluk, Eric ^{[1
]}

机构：

[1] CNRS, UMR 8107, LML, F-59650 Villeneuve Dascq, France

[2] Ecole Cent Lille, F-59650 Villeneuve Dascq, France

[3] CNRS, Lab Mat Ingn & Sci MATEIS, INSA Lyon, UMR 5510, F-69621 Villeurbanne, France

来源：

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS | 2014年 / 324卷

关键词：

Cast aluminium silicon alloys; Digital Image Correlation; Laboratory X-ray CT; SYNCHROTRON TOMOGRAPHY; ALUMINUM-ALLOYS; FATIGUE; POROSITY; FOAM;

D O I：

10.1016/j.nimb.2013.07.034

中图分类号：

TH7 [仪器、仪表];

学科分类号：

0804 ; 080401 ; 081102 ;

摘要：

In cast aluminium alloys used in the automotive industry the microstructure inherited from the foundry process has a strong influence on the mechanical properties. In the cylinder heads produced by the Lost Foam Casting process, the microstructure consists of hard intermetallic phases and large gas and microshrinkage pores. To study its influence, full field measurements at the microstructure scale were performed during a tensile test performed in situ under X-ray microtomography. Intermetallics were used as a natural speckle pattern. Feasibility of Digital Volume Correlation on this alloy was proved and the accuracy of the measurement was assessed and discussed in light of the small volume fraction of intermetallics and in comparison with the accuracy of Digital Image Correlation performed on optical images at a finer spatial resolution. (C) 2013 Elsevier B.V. All rights reserved.

引用

页码：57 / 62

页数：6

共 50 条

[31] Effect of withdrawal rate on microstructure of a hypoeutectic Al-Si alloy by low superheat DC casting
Zhao Dazhi
Liu Fang
Yu Fuxiao
Hong Tao
Zuo Liang
China Foundry, 2013, 10 (03) : 172 - 175
[32] Study on Solidification Microstructure of Melt Supercooled Hypereutectic Al-Si Alloy
Zhou H.
Liu Y.
Wu C.
Wang J.
Su X.
Cailiao Daobao/Materials Reports, 2023, 37 (12):
[33] Influence of cryorolling on microstructure and mechanical properties of a cast hypoeutectic Al-Si alloy
Immanuel, R. J.
Panigrahi, S. K.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 640 : 424 - 435
[34] Effect of withdrawal rate on microstructure of a hypoeutectic Al-Si alloy by low superheat DC casting
Zhao Dazhi
Liu Fang
Yu Fuxiao
Hong Tao
Zuo Liang
CHINA FOUNDRY, 2013, 10 (03) : 172 - 175
[35] Hardness control of Al-Si HPDC casting alloy via microstructure refinement and tempering parameters
Kasprzak, Wojciech
Kurita, Hirotaka
Birsan, Gabriel
Amirkhiz, Babak Shalchi
MATERIALS & DESIGN, 2016, 103 : 365 - 376
[36] Microstructure and corrosion behaviour of Al-Si alloy treated by high intensity ultrasonic vibrations
El Nashar, Rana M.
El-Aziz, Ahmed M.
Khalifa, Waleed
El Ghani, Nour T. Abd
OCHRONA PRZED KOROZJA, 2012, 55 (02): : 34 - 38
[37] Compressive behaviour of open-cell Al-Si alloy foam produced by infiltration casting
Xia, Yinzheng
Shi, Jianchao
Mu, Yongliang
MATERIALS SCIENCE AND TECHNOLOGY, 2023, 39 (16) : 2433 - 2445
[38] Determination of strontium segregation in modified hypoeutectic Al-Si alloy by micro X-ray fluorescence analysis
Nogita, K.
Yasuda, H.
Yoshida, K.
Uesugi, K.
Takeuchi, A.
Suzuki, Y.
Dahle, A. K.
SCRIPTA MATERIALIA, 2006, 55 (09) : 787 - 790
[39] WEAR BEHAVIOUR OF A413 Al-Si ALLOY CASTING SUBJECT TO DIFFERENT COOLING RATES
Mohandass, M.
Venkatesan, A.
JOURNAL OF THE BALKAN TRIBOLOGICAL ASSOCIATION, 2014, 20 (03): : 479 - 487
[40] The X-ray measurement of the thermal expansibility of Al-Si alloy in the form of a cast and a protective coating on steel
Kucharska, B.
Wrobel, A.
Kulej, E.
Nitkiewicz, Z.
APPLIED CRYSTALLOGRAPHY XXI, 2010, 163 : 286 - 290

← 1 2 3 4 5 →