Testing and modelling of a variable speed scroll compressor

被引:77
|
作者
Cuevas, Cristian [1 ]
Lebrun, Jean [2 ]
机构
[1] Univ Concepcion, Fac Ingn, Dept Ingn Mecan, Concepcion, Chile
[2] Univ Liege, Thermodynam Lab, B-4000 Liege, Belgium
关键词
Scroll compressor; Variable speed; Testing; Modelling; Inverter efficiency; Isentropic efficiency; Volumetric efficiency; REFRIGERANT INJECTION; PERFORMANCE; CAPACITY;
D O I
10.1016/j.applthermaleng.2008.03.016
中图分类号
O414.1 [热力学];
学科分类号
摘要
Variable speed compressors offer continuous control, low noise level, reduced vibration, low-start current, rapid temperature control, by operating the compressor at higher speeds initially, and better COPs than the conventional on/off control. However, there exist some drawbacks concerning the inverter efficiency, the effect of the inverter on the induction motor and the effect of variable speed on the compressor isentropic and volumetric efficiencies. This study gives some experimental results as to inverter and compressor performances: it can be observed that the inverter efficiency varies between 95% and 98% for compressor electrical power varying between 1.5 and 6.5 kW : and that compressor efficiencies are not enormously influenced by compressor supply frequency, but depend mainly on compressor pressure ratio, except the tests developed at 35 Hz and one test at 40 Hz, for which the difference is attributed to the compressor internal leakages due to a lack of lubrication at low speeds. At 75 Hz there was also observed a slight degradation that can be attributed to the electromechanical losses that increase with compressor speed. A maximal isentropic efficiency of 0.65 for a pressure ratio of the order of 2.2 is obtained. The volumetric efficiency decreases linearly from 0.98 for a pressure ratio of 1.5 to 0.83 for a pressure ratio of 5.6. In spite of the test conditions (condensing and evaporating pressures up to 40 and 20 bar, respectively). the compressor performance stays unchanged. The experimental results obtained at 50 Hz are used to identify six parameters of a semi-empirical model which is then used to simulate the different tests developed at different compressor speeds. The simulated results are in very good agreement with those measured with averages errors of -0.5 K: +3 g s(-1) and -24 W for the exhaust temperature, the refrigerant flow rate and the compressor electrical power, respectively. The results show that motor losses induced by the inverter are negligible. (C) 2008 Elsevier Ltd. All rights reserved.
引用
收藏
页码:469 / 478
页数:10
相关论文
共 50 条
  • [41] Geometrical Model and Optimization of Scroll Compressor Based on Involute of Circle with Variable Radii
    Peng B.
    Liu H.
    Tao Y.
    [J]. Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University, 2023, 57 (08): : 1046 - 1054
  • [42] Performance evaluation of a variable speed DC compressor
    Ekren, Orhan
    Celik, Serdar
    Noble, Brad
    Krauss, Ryan
    [J]. INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 2013, 36 (03): : 745 - 757
  • [43] CHARACTERIZATION METHODOLOGY FOR VAPOR INJECTION SCROLL COMPRESSORS OF VARIABLE SPEED
    Tello-Oquendo, Fernando M.
    Vasconez-Nunez, Daniela C.
    Navarro-Peris, Emilio
    Corberan, Jose M.
    [J]. COMPRESSORS 2021 - 10TH IIR CONFERENCE ON COMPRESSORS AND REFRIGERANTS, 2021,
  • [44] The Design of Scroll compressor Scroll Plate Matching System
    Liu, Guoping
    Chen, Zhongyang
    Yang, Juan
    Hu, Ronghua
    [J]. FRONTIERS OF MANUFACTURING AND DESIGN SCIENCE III, PTS 1 AND 2, 2013, 271-272 : 1201 - 1205
  • [45] ON THE PROFILE DESIGN OF A SCROLL COMPRESSOR
    LEE, YR
    WU, WF
    [J]. INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 1995, 18 (05): : 308 - 317
  • [46] Scroll compressor simulation model
    Schein, C
    Radermacher, R
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2001, 123 (01): : 217 - 225
  • [47] On the profile design of a scroll compressor
    [J]. Int J Refrig, 5 (308-317):
  • [48] Surface texturing in scroll compressor
    Kawabata, Sanemasa
    [J]. Toraibarojisuto/Journal of Japanese Society of Tribologists, 2015, 60 (04): : 268 - 273
  • [49] DESIGN OPTIMIZATION OF THE SCROLL COMPRESSOR
    ETEMAD, S
    NIETER, J
    [J]. INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 1989, 12 (03): : 146 - 150
  • [50] MODELLING OF THE VARIABLE SPEED DRIVE WITH SPEED OBSERVER
    Rinkeviciene, Roma
    Kriauciunas, Jonas
    [J]. ELECTRICAL AND CONTROL TECHNOLOGIES, 2010, : 215 - 218