Performance of wrought aluminium and magnesium alloy tubes in three-point bending

被引：46

作者：

Hilditch, Tim ^{[1
]}

Atwell, Dale ^{[1
]}

Easton, Mark ^{[2
]}

Barnett, Matthew ^{[1
]}

机构：

[1] Deakin Univ, CMFI, CAST Cooperat Res Ctr, Geelong, Vic 3217, Australia

[2] Monash Univ, Dept Mat Engn, CAST Cooperat Res Ctr, Clayton, Vic 3800, Australia

来源：

MATERIALS & DESIGN | 2009年 / 30卷 / 07期

关键词：

Non-ferrous metals and alloys; Wrought; Extrusion; MICROSTRUCTURE;

D O I：

10.1016/j.matdes.2008.11.020

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This present work examines the load carrying capacity, energy absorption and fracture characteristics of wrought magnesium and aluminium alloy tubes in three-point bending. Magnesium alloy AZ31, and aluminium alloys 6063 and 7075, were extruded into cylindrical tubes of both equivalent thickness and mass. A strong thickness effect was present meaning that the AZ31 tube had significantly higher load and energy absorption performance than an equivalent mass 6063 tube, albeit not as high as the 7075 tube. Hinge formation and maximum load was delayed for the magnesium alloy, meaning that a high energy absorption rate persisted to higher deformation displacements than the aluminium alloys. It was also found that fracture during deformation was dependent on the indenter diameter, tube thickness and lower support separation. (c) 2008 Elsevier Ltd. All rights reserved.

引用

页码：2316 / 2322

页数：7

共 50 条

[21] STRUCTURAL RESPONSE OF ALUMINIUM FOAM HYBRID SANDWICH PANELS UNDER THREE-POINT BENDING LOADING
Kabir, Kaveh R.
Vodenitcharova, Tania
Hoffman, Mark
INTERNATIONAL JOURNAL OF MODERN PHYSICS B, 2009, 23 (6-7): : 1733 - 1738
[22] Three-point Bending Fracture Behaviors of Bamboo
An, Yuanlin
Liu, Zhiming
Wang, Gan
Wu, Wenjian
ADVANCES IN BUILDING MATERIALS, PTS 1-3, 2011, 261-263 : 464 - 468
[23] Three-Point Bending of Seven Layer Beams
Magnucki, Krzysztof
Witkowski, Dawid
Kedzia, Piotr
COMPUTATIONAL TECHNOLOGIES IN ENGINEERING (TKI'2018), 2019, 2078
[24] Three-point bending test of fiber posts
Mannocci, F
Sherriff, M
Watson, TF
JOURNAL OF ENDODONTICS, 2001, 27 (12) : 758 - 761
[25] Springback Behavior of AA6082T6 Tubes in Three-point Bending Operation
Sofuoglu, Mehmet Alper
Gurgen, Selim
Cakir, Fatih Hayati
Orak, Sezan
7TH INTERNATIONAL CONFERENCE ON ENGINEERING, PROJECT, AND PRODUCTION MANAGEMENT, 2017, 182 : 658 - 664
[26] The three-point bending test, a critical review
Bagheri, M
PROCEEDINGS OF THE EIGHTH JAPAN-U.S. CONFERENCE ON COMPOSITE MATERIALS, 1999, : 683 - 692
[27] Three-point bending behavior of a ZEK100 Mg alloy at room temperature
Aslam, I.
Li, B.
McClelland, Z.
Horstemeyer, S. J.
Ma, Q.
Wang, P. T.
Horstemeyer, M. F.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 590 : 168 - 173
[28] Forming Characteristics of Tailor Rolled Blank of Aluminum Alloy during Three-Point Bending
Zhi, Ying
Feng, Yue
Wang, Dong
Hu, Xianlei
Sun, Tao
Liu, Xianghua
MATERIALS, 2024, 17 (03)
[29] Performance of aluminium/Terocore® hybrid structures in quasi-static three-point bending: Experimental and finite element analysis study
Rathnaweera, Gayan
Ruan, Dong
Hajj, Michael
Durandet, Yvonne
MATERIALS & DESIGN, 2014, 54 : 880 - 892
[30] Study on three-point bending mechanical performance of thin-walled super alloy honeycomb sandwich with penetrable defects
Yang, Kai
Liu, Liwu
Yu, Kaiping
Kong, Xianghao
ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-3, 2011, 314-316 : 1203 - +

← 1 2 3 4 5 →