Collapse of periodic planar lattices under uniaxial compression, part I: Quasi-static strength predicted by limit analysis

被引:66
|
作者
Qiu, X. M. [1 ,2 ]
Zhang, J. [1 ]
Yu, T. X. [2 ]
机构
[1] Tsinghua Univ, Dept Engn Mech, Beijing 100084, Peoples R China
[2] Hong Kong Univ Sci & Technol, Dept Mech Engn, Kowloon, Hong Kong, Peoples R China
基金
美国国家科学基金会;
关键词
Planar lattices; Collapse strength; Energy absorption; Kinematical admissible field; Static;
D O I
10.1016/j.ijimpeng.2009.05.011
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
The collapse strength is analyzed for typical periodic planar lattices under uniaxial compression. In this part, the quasi-static strengths of the lattices are predicted by limit analysis, with the consideration of the elastic effect and large deformation effect. The planar lattices are firstly classified into bending-dominated and membrane-dominated structures. Collapse strength of typical bending-dominated lattices, such as hexagonal and rhombus structures, has identical initial lower bound and upper bound, so that the equivalent stress-strain curve of a bending-dominated lattice possesses a plateau. On the contrary, the equivalent stress-strain curve of a membrane-dominated lattice, such as square, triangular or Kagome structure, usually contains a peak followed by a sharp drop without a plateau. Consequently, the energy absorption behavior of the bending-dominated lattices is similar to type I structure, while that of the membrane-dominated lattices is similar to type II structure. (C) 2009 Elsevier Ltd. All rights reserved.
引用
收藏
页码:1223 / 1230
页数:8
相关论文
共 43 条
  • [21] Rods glued in engineered hardwood products part I: Experimental results under quasi-static loading
    Grunwald, Cordula
    Vallee, Till
    Fecht, Simon
    Bletz-Muehldorfer, Oliver
    Diehl, Friedemann
    Bathon, Leander
    Myslicki, Sebastian
    Scholz, Ronja
    Walther, Frank
    INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2019, 90 : 163 - 181
  • [22] Strength analysis of carbon-fiber dovetail tenon connections under quasi-static tension
    Qin, Yuhang
    Xiong, Chao
    Zhu, Xiujie
    Yin, Junhui
    Zhang, Yu
    Fan, Zhaoyang
    Liu, Zhao
    Zhang, Wei
    STRUCTURES, 2024, 67
  • [23] Weibull master curves and fracture toughness testing Part I Master curves for quasi-static uniaxial tensile and bend tests
    M. Lambrigger
    Journal of Materials Science, 1999, 34 : 667 - 673
  • [24] Weibull master curves and fracture toughness testing - Part I - Master curves for quasi-static uniaxial tensile and bend tests
    Lambrigger, M
    JOURNAL OF MATERIALS SCIENCE, 1999, 34 (04) : 667 - 673
  • [25] Quasi-static compression and energy absorption behaviour of polymeric selective laser sintered open cell lattices under varying relative densities
    Kumar, K. Mohan
    Arumaikkannu, G.
    RAPID PROTOTYPING JOURNAL, 2024, 30 (04) : 643 - 661
  • [26] Energy Analysis Method for Uniaxial Compression Test of Sandstone under Static and Quasi-Dynamic Loading Rates
    Liu, Zhixi
    Zhao, Guangming
    Meng, Xiangrui
    Zhang, Ruofei
    Chunliang, Dong
    Xu, Wensong
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2021, 2021
  • [27] Comparison of Porcine Brain Tissue with Potential Surrogate Materials Under Quasi-static Compression and Dynamic Mechanical Analysis
    Singh, D.
    Boakye-Yiadom, S.
    Cronin, D. S.
    CHALLENGES IN MECHANICS OF TIME-DEPENDENT MATERIALS (2018), VOL 2, 2019, : 57 - 59
  • [28] Numerical and experimental studies on the limit state of fibre-reinforced composite columns with a lipped channel section under quasi-static compression
    Debski, Hubert
    Teter, Andrzej
    COMPOSITE STRUCTURES, 2015, 133 : 1 - 7
  • [29] Quasi-static analysis of thrust-loaded angular contact ball bearings part I: theoretical formulation
    Chen Wenhua
    Ma Zikui
    Gao Liang
    Li Xinglin
    Pan Jun
    CHINESE JOURNAL OF MECHANICAL ENGINEERING, 2012, 25 (01) : 71 - 80
  • [30] Quasi-static analysis of thrust-loaded angular contact ball bearings part I: theoretical formulation
    Wenhua Chen
    Zikui Ma
    Liang Gao
    Xinglin Li
    Jun Pan
    Chinese Journal of Mechanical Engineering, 2012, 25 : 71 - 80