Design and Development of Thermoelectric Cooler to Control Mold Temperature in Injection Molding Machine

被引：1
|
作者：
Fadzly, M. K. [1 ,2 ,3 ]
Mardhiati, M. M. [1 ]
Foo, W. T. [1 ]
Fakhira, W. N. [1 ]
机构：
[1] Univ Malaysia Perlis, Ctr Diploma Studies CDS, S2-L1-26 Kampus UniCITI Alam Sg, Padang Besar U 02100, Perlis, Malaysia
[2] Univ Malaysia Perlis, Sch Mfg Engn, Kampus Tetap Pauh Putra, Arau 02600, Perlis, Malaysia
[3] Univ Malaysia Perlis, Ctr Excellence Geopolymer & Green Technol CEGeoGT, Green Design & Manufacture Res Grp, Kangar 01000, Perlis, Malaysia
来源：
5TH INTERNATIONAL CONFERENCE ON GREEN DESIGN AND MANUFACTURE 2019 (ICONGDM 2019) | 2019年 / 2129卷
关键词：
COOLING SYSTEM; OPTIMIZATION; QUALITY;
D O I：
10.1063/1.5118156
中图分类号：
X [环境科学、安全科学];
学科分类号：
08 ; 0830 ;
摘要：
One of the basic problems in the development and production process of molds for injection molding is the control of temperature conditions in the mold. Mold temperature control is one of the most important parameters in injection molding process of thermoplastics. Mold temperature should be controlled so that the mold temperature is in the right accordance with the standard specifications of plastic to ensure the quality of plastic produced is consistent. This project is focused on designing and developing thermoelectric cooler for controlling mold temperature in injection molding using Arduino UNO. The design for this project is selected by using Pugh Method. This project is done by clamping thermoelectric peltier between the water-cooling block. Arduino UNO and relay that are used to control temperature sensor and water pump at the hot and cold side. Testing data is obtained from the Arduino UNO that is connected to the temperature sensor. Based on the testing result, this project is working well but it needs some modifications for improvement before it can be used in the injection molding machine.
引用
收藏
页数：6
相关论文
共 50 条
  • [21] DEVELOPMENT STEPS FOR AUTOMATED INJECTION-MOLDING OF CROSSLINKABLE MATERIALS .2. MACHINE AND MOLD TECHNOLOGY FOR THE INJECTION-MOLDING OF RUBBER
    BARTH, P
    KAUTSCHUK GUMMI KUNSTSTOFFE, 1988, 41 (08): : 801 - 804
  • [22] Temperature Control for MEMS Gyroscope with Thermoelectric Cooler
    Wang, Zhenjun
    Yue, Yanjun
    Zhou, Yi
    Ke, Zhaorong
    Jiang, Bo
    Zhou, Tong
    Su, Yan
    2024 IEEE 19TH INTERNATIONAL CONFERENCE ON NANO/MICRO ENGINEERED AND MOLECULAR SYSTEMS, NEMS 2024, 2024,
  • [23] Integrative Approaches for Mechanical Mold Design in Injection Molding
    Hopmann, Christian
    Erler, Ivo
    PLASTICS ENGINEERING, 2013, 69 (06) : 50 - 54
  • [24] INJECTION-MOLDING ABS? MOLD IN QUALITY WITH THE MACHINE.
    Fritch, Lee
    Plastics Engineering, 1979, 35 (05): : 68 - 72
  • [25] Injection Molding Simulation with Variothermal Mold Temperature Control of Highly Filled Polyphenylene Sulfide
    Birkholz, A.
    Tschiersky, M.
    Wortberg, J.
    PROCEEDINGS OF PPS-30: THE 30TH INTERNATIONAL CONFERENCE OF THE POLYMER PROCESSING SOCIETY, 2015, 1664
  • [26] Design and Development of Controller for Thermoelectric Cooler System
    Firdaus, A. Z. Ahmad
    Zolkifly, M. Z.
    Syahirah, K. N.
    Normahira, M.
    Aqmariah, S. N.
    Ismail, I. I.
    PROCEEDINGS 5TH IEEE INTERNATIONAL CONFERENCE ON CONTROL SYSTEM, COMPUTING AND ENGINEERING (ICCSCE 2015), 2015, : 264 - 268
  • [27] Passive mold temperature control by a hybrid filming-microcellular injection molding processing
    Chen, Shia-Chung
    Li, Hai-Mei
    Hwang, Shyh-Shin
    Wang, Ho-Hsiang
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2008, 35 (07) : 822 - 827
  • [28] Injection molding machine temperature control method based on time optimization
    College of Information and Electrical Engineering, Shandong University of Science and Technology, Qingdao 266510, China
    Yi Qi Yi Biao Xue Bao, 2008, 3 (633-637):
  • [29] The method of improving precision of micro injection molding machine temperature control
    Tang ShengDe
    Xu Hong
    Wu Daming
    Zhang Yajun
    ADVANCED MATERIALS DESIGN AND MECHANICS II, 2013, 372 : 354 - +
  • [30] Influence of Heat Sink on the Mold Temperature of Gypsum Mold Used in Injection Molding
    Lin, Chung-Chih
    Chen, Kun-Chen
    Yeh, Hon-Chih
    POLYMERS, 2020, 12 (03)
12345