Experimental Study of Microgroove Surface Using Three-Dimensional Elliptical Vibration Texturing

被引:13
|
作者
Kurniawan, Rendi [1 ]
Ali, Saood [1 ]
Park, Ki Moon [1 ]
Jung, Sang Tae [2 ]
Ko, Tae Jo [1 ]
机构
[1] Yeungnam Univ, Precis Machining Lab, Dept Mech Engn, Room 214, Gyongsan 38541, South Korea
[2] Pohang Univ Sci & Technol, Pohang Accelerator Lab, Pohang Si 37673, South Korea
来源
基金
新加坡国家研究基金会;
关键词
microgroove; vibration mark; 3D-EVT; microstructured surface; DIMPLE FORMATION; PERFORMANCE; GENERATION; TOPOGRAPHY; ALLOY;
D O I
10.1115/1.4043957
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
This paper presents our preliminary study of the microstructured surface on microgrooves patterns, which have manufactured using the three-dimensional elliptical vibration texturing (3D-EVT) method. The 3D-EVT method uses a three-dimensional trajectory of elliptical locus of the cutting tool tip in high vibration frequency to fabricate the microstructure or the vibration mark pattern on the machined surface. The experimental study has been done with a variation of the nominal cutting speeds from 300 to 600 mm/min. The preliminary results showed that in the low nominal cutting speed of 300 and 450 mm/min, the microstructured surfaces were not manufactured well due to the bulging existence on the microstructured surface in which it is correlated with the build-up edge phenomena. On the other hand, a relative excellent microstructured surface can be achieved at the higher nominal cutting speed of 600 mm/min. In addition, a lubricant could be used to obtain an excellent microstructured surface to avoid the built-up edge phenomena.
引用
收藏
页数:7
相关论文
共 50 条
  • [21] Experimental study of cutting forces and surface topography in three-dimensional vibration-assisted milling for fabricating structured surfaces
    Wang, Guilian
    Xiao, Mengjie
    Liu, Wenrui
    Lv, Bingrui
    Xu, Jinyou
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 133 (3-4): : 1285 - 1303
  • [22] Coupling relationship between three-dimensional vibration of the crankshaft and surface vibration of the crankcase
    Shu, Gequn
    Liang, Xingyu
    Nongye Gongcheng Xuebao/Transactions of the Chinese Society of Agricultural Engineering, 2006, 22 (01): : 1 - 5
  • [23] Experimental and analytical study of ultrasonic elliptical vibration cutting on AISI 1045 for sustainable machining of round-shaped microgroove pattern
    Kurniawan, Rendi
    Kumaran, S. Thirumalai
    Ali, Saood
    Nurcahyaningsih, Dwi Ayu
    Kiswanto, Gandjar
    Ko, Tae Jo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 98 (5-8): : 2031 - 2055
  • [25] Experimental and analytical study of ultrasonic elliptical vibration cutting on AISI 1045 for sustainable machining of round-shaped microgroove pattern
    Rendi Kurniawan
    S. Thirumalai Kumaran
    Saood Ali
    Dwi Ayu Nurcahyaningsih
    Gandjar Kiswanto
    Tae Jo Ko
    The International Journal of Advanced Manufacturing Technology, 2018, 98 : 2031 - 2055
  • [26] A novel three-dimensional elliptical vibration cutting device based on the freedom and constraint topologies theory
    Lin, Sheng
    Kong, Xi
    Wang, Chun
    Zhai, Yun
    Yang, Liang
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2019, 233 (03) : 675 - 685
  • [27] Experimental study three-dimensional wave breaking
    She, K.
    Greated, C.A.
    Easson, W.J.
    Journal of Waterway, Port, Coastal and Ocean Engineering, 1994, 120 (01) : 20 - 36
  • [28] Camouflage using three-dimensional surface disruption
    King, Jemma
    Hemmi, Jan M.
    Kelley, Jennifer L.
    BIOLOGY LETTERS, 2023, 19 (08)
  • [29] Vibration analysis and experimental study of three-dimensional orthogonally coupled plates with through edge cracks
    Yang, Cheng
    Chen, Yue
    Niu, Yanhui
    Zhao, Tiantong
    Jin, Guoyong
    THIN-WALLED STRUCTURES, 2024, 203
  • [30] An experimental investigation of the three-dimensional vibration characteristics of ultrasonic irrigation tips
    Dannemann, M.
    Kucher, M.
    Weber, M-T.
    Modler, N.
    PROCEEDINGS OF INTERNATIONAL CONFERENCE ON NOISE AND VIBRATION ENGINEERING (ISMA2018) / INTERNATIONAL CONFERENCE ON UNCERTAINTY IN STRUCTURAL DYNAMICS (USD2018), 2018, : 2337 - 2348